RB525HC General Electric Range - Instructions

Disconnected power supply to range, pull top back metal cover, pull wires from burner on/off switch,and removed one screw that holds block in place. Installed new terminal block by placing screw back on block & placing wires back on the on/off switch.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

Replacing the Surface Burner Terminal Block Kit was very easy.

1. Pull the stove from the wall a little so you can have space to work. I unplug the stove from lthe 220 outlet. Then remove the Surface Burner element.

2. Then we removed the back pannel from the stove by removing the screws with a nut driver. Only four screws to remove.

3. Once the pannel was removed. I Unpluged the wires from the stove pannel. Being careful not to damage the plug in. There were only two wires to unplug. So trace the wires to make sure you are unpluging the correct one.

4. Lift the top up on the stove and unscrewed the Terminal Block from the top of stove. We only have one screw there.

5. Pull the Terminal Block and wires out and replace with the new Terminal Block, making sure the wires were feed along the side under the top of stove so they can not be damaged. Plug in wires and replace pannel.

The wire to the burners were old and needed replacement. When the new terminals arrived, my husband had gone hunting. When the parts arrived, I pulled the stove away from the wall and found the nut driver that I needed. I removed the screw on the terminal box under the burner and realized I had to remove the back panel of the stove. I unplugged the old wires and plugged in the new ones. I installed the new terminal boxes under the burners and plugged the burners back in. My stove works like new and I am thrilled that it was so easy. Thanks

followed the instruction from your video an it was a snap

Just had to change out the drip bowls, easy. But, I wanted to comment on the quick delivery on the new bowls. I was impressed. Thank you.

Took the old pans out and put the new ones in. Simple as pie

I needed to replace all stovetop bowls and found all after-market bowls "just a little off" effecting how flat the burner rested so called PartSelect's hotline and was assured that if I were using the actual model number found on the stove the parts would definitely fit and not almost fit, guaranteed, and they did!

First I shut off the breakers. I cut the wire from the end of the new part and took off the plastic off because the end of the new wire has a special end clamp to connect to the old wire which is in the stove but that wire didn't have the same clamp to be able to connect them together therefore I needed to cut the wire to from the new part also and connect it to the old wire with a wire nut which is on the range which is attached to all the other burners. Twisted them together and I put a wire nut to hold them strong together, pushed in the end of the burner into the 2 holes of this new part. I turned on the breakers.

Dropped in new bowls. I was surprised how in-expensive new ones were.