JGSP31GEP3 General Electric Range - Instructions

Called in and talked to someone and he look yup what he thought was correct but after i got them theywere wrong so i sent them back for a full refund minus 9.90 freight. I still need to figure out what i need for my 27 inch wall oven. Please help. Thanks

Remove oven door from hinges, by pulling it straight up and off, (like you would do for closer access to clean inside). Remove the storage drawer. Lift up and away off the track, (like a file cabinet drawer). With the drawer out and away, you can see how the springs are easily detached from each hinge. Note the location of where the springs attach to the hinges, and bottom of stove. Remove each spring. Three screws on each side hold the hinges on. Unscrew, and set them aside. (The new hinges did not have new screws in package.) Place new hinge in place. Reinstall in reverse of disassembly. If any part of the door or face of the stove (where hinges mount) was bent slightly due to forcing door open, reform with light hammer taps and C-clamps. Enjoy for ANOTHER 10+ years, because it's a GE Profile Stove : )

REMOVED DOOR TO OVEN
REMOVED HINGE [3 SCREWS]
REMOVED BOTTOM DRAW
UNHOOKED SPRING FROM LEFT SIDE ATTACHED TO HINGE
PULL OUT DEFECTIVE HINGE
REPLACE WITH NEW HINGE AND SCREWS
REHOOK SPRING TO HINGE & REPLACE DOOR
COMPLETE

FOLLOW VIDEO PROVIDED BY PARTS SELECT

After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.

I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.

1) Verified it was the broiler igniter that was damaged.
2) Removed the oven door, the lower pot storage drawer and the top range panel.
3) Turned off the gas supply in the top range area. Pulled the electrical plug-in out of the lower electrical panel (behind the lower drawer).
4) Used the nut driver to remove the two (2) 1/4" screws that held the igniter to the back wall of the oven. I later read in the Use & Care Guide that this is easier to do if the broiler burner cover is removed first.
5) I pulled the damaged igniter away from the back wall, expecting to expose wire connectors or splicing but was only able to get about 6" of the two (2) insulated wires before I could not pull them any further.
6) Therefore, I cut the wires and, without a proper wire stripper, cut about 3/8" of insulation away in order to make a splice between the wiring from the new igniter and the wiring coming out of the back of the oven. Big mistake ..... do not recommend this without using a proper wire stripper! I must have cut into the existing exposed oven wiring on one of the wires such that when I used the twist-on to make the splice, most of the wires (those wound together to form one wire) were damaged and broke away. Unfortuantely I did not find this out until everything was put back together and we (my wife and I) did the test. No results!
7) I took everything apart again and when I tried to pull the wiring back out from in behind the oven wall, one wire came out with the twist-on in tact and the other came out "with no wire attachment".
8) I now had to figure out how to get into the back of the oven to retrieve the "lost connecting wire". It is quite simple when you know what you are doing but no instructions (that I had) advised that the upper back light gauge metal panels could be easily removed to expose the wiring. This was eventually determined and the connections were both made again in a more positive manner.
9) We (my wife and I) put it all back together and this time it was fine ..... just had to be patient while the gas purged the air out of the broiler burner line.
10) Lessons learned: GE made it easy "once you knew how it could be done". I suspect GE feels that service type people should be doing these things but with a 120VAC (vs higher voltage electric type ovens) system why not provide the info for the "do-it-yourselfers" as well?

Real simple. Disengaged springs at the inside bottom, replaced hinges and reengaged springs.

1. I have searched info on the internet and found that site.
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel

/||\
||

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm

• Start by unplugging the unit from the wall.
• Then slide the unit out carefully without damaging the gas line.
• Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools.
• Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is.
• Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place.
• Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is.
• Remove the igniter 1-2 screws
• Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered****
• Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under****
• Reassemble the range and replace the drawer.
• Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.

Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...And then I installed
ignitor tightening the two screws and connected the two ignitor wires with the provided wire-nuts.
Mike Polcho

It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the burner tube back in place and secured it with the screw, replace oven bottom and door the whole repair took 20 minutes.

IThe schematics on the website were helpful for how everything goes together. I just followed the picture and then unscrewed all the screws that held the ignitor to the gas pipe. Have to pull out the gas pipe out first so you can get to the bolts, easy to do when you pull out the drawer and unscrew the hold down for the gas pipe.

No directions came with the part, and the length of the new wires weren't long enough nor did they have the attachment pieces that are needed to plug in the wires. However, helpful tips from others on the website told me that you have to cut the wires off the old part and screw the wires from the old to the new with the white plastic wire couplings. Worked like a charm!

It was a simple procedure, and I saved myself buying a new stove or paying someone else to fix it!