JF1601 General Electric Range - Instructions

I removed the screws holding the element in place. I pulled the element out from the back of the oven about 3" and then disconnected the two wires. I then reattached the two wires to the new element and pushed the element back flush with the rear of the oven. I then rescrewed the two screws that hold the element in place. That was all there was to it.. Very easy. I am 54 years old and have never done this before.. So if I can do it so can you....

I was worried at being able to locate the part as the oven is over 35 years old. I put in the old part number on your site and it gave me the correct replacement. On my model you unscrew the two screws securing the element to the back of the oven. Then pull out the old element carefully because the wires are screwed onto the element. I pulled it out 4 or 5 inches and unscrewed the wires and connected the wires to the new element. I then threaded the wires back into the hole at the back of the oven and screwed the element back in place. Works perfect.

First, turn off the power. Remove the two retaining screws, pull out the broken element far enough to unscrew the connectors, remove the element, reconnect the new element, screw it back in, turn the power back on. Yes, it is that easy! Took me all of five minutes. Took longer to find my tools!

Removed the screws. Pulled out the element and disconnected the wires. Attached the wires from the new heating element and screwed it in.

Removed 2 mounting screws - Removed 2 screws used to attach wiring to element. Received new element and re-attached the 4 screws.

Tried contacting GE and no luck, they did not have vintage parts. After searching and locating Partselect, I was able to see a pic of the actual replacement part. I wasn't sure about purchasing online (1st timer) but decided to go for it!

I was able to track the package, although FedEX was setup to deliver to my resdient, I had the package addressed to my office but we worked that out also and walla.

I was very please and now I can bake my famous Pot Roast again. The oven was not working for 8 mos.

Good Eaten!

SJ-Long Beach CA

I ordered the bake element on Monday and received it on Wednesday. Great delivery.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
Then I installed the new element using the steps above in reverse. Very clean and simple. One tip though...open your oven door slightly to the detent and pull straight up. The door slips off easily and allows easy access to the bake element screws.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I reattached them to the new element screwed it back in place and I was done. Could not have been easier! Getting the right replacement part the next day after placing the order was a pleasant surprise. This is the second time I used your company and I am very impressed with your service. I recommend you to everyone I can. Great Job!

Turn off the breaker. Unscrew the element. Remove and replace with new element. Screw it back into place. Turn on the breaker.

That simple, that easy.

First I removed the two screws that hold the element in place. I then pulled the element out about 2 inches and disconnected the two wires.

I reconnected the two wires to the new element and screwed the new element to the wall of the oven where the element was held in place.

First removed screws then removed burned out element.Replaced with new element and replaced screws and cooked pizza.

It was realatively simple, turned off the power to the oven, removed the bake element , by loosening the two metal screws in the back of the oven, with a nut driver and removing the screws, then pulling the element outward, to expose the two wires ,that were connected to the element, using a nut driver to remove the two screws and a pair of pliers to hold the wire connectors, then removed the old element. Installed the new bake element, by connecting the two wires to the element, with the two screws, then pushing the element back in place , attaching the element to the back of the oven, with the two metal screws, finished with the installation, turned power back to the oven , and tested to make sure the oven worked , all done.

Repair was easy.
Note: the element leads have a potential across them,
so unplug the unit or you'll have an arc strike.

I liked the selection method at PartsSelect.com.
Finding the replacement part was easy from the pictures.
The prices were reasonable.

The part came next day, which was a surprise.
Removal and Installation was 4 screws.
I have become a DIY hero.

Only downside was going out for dinner every night ended.
This site is now a Favorite.

The delivery of the part was within 3 days.I only had to connect the two screws had biscuits that night.

Once I watched the video pertaining to the installation of the part, the job was very easy.