JKP55G4D1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ernie from Gualala,Ca, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old burner had burned out and broken
removed old element and installed new, and oven is up and working like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William M. from Towaco, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element went dead
Removed access screws from bake element cover, removed screws retaining wire connections on bake element, reverse procedure, and heat to burn off contaminants.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Houston, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven bake element broken
Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOE from WESTON, CT
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned Out Lower Heating Element
Unscrewed the old one and screwed in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Sugar Land, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element burned out
Turned off the breaker. Removed 2 screws and pulled the element from encasement. Removed 2 screws holding the wires to the element.
Reversed the process to install the new coil.
Done in 10 minutes
Reversed the process to install the new coil.
Done in 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from kersey, PA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven element burned out
removed the element with 2 screws. disconected element with 2 screws. reversed order to install new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Litchfield Park, AZ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element would no longer heat up.
Shopped online for a good price for the heating element. Thw element came very quickly, very good packaging. Removed and replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from Glenmont, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Broken Bake Element in Oven
Unscrewed face plate, unscrewed electric wires hooked to element. Cleaned out oven while I was in there...nice and clean now. Installed new element same way I took it out. Easy as 'pie'..which we'll be baking again now that the oven works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from West Springfield, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
burned out bake element
The repair was a snap! Unscrew the two small bolts holding the back of the element in place. Pull out the element so that the connectors and wires are accessible. Unscrew the two wires from the element. Remove old element. Place new element in oven. Attach the two wires to the new element (two screws), place the new element in position and replace the two small bolts that were removed at the beginning. All done. Best thing? This is a 20 year old oven, GE didn't even have the part I needed. You did! Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Andover, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element hot spots and deformed
Looked up mfg. and part #,looked at blow up of stove on parts select, identified element. The part came overnite. Shut down power, removed 2 screws with a nut driver, pulled element foreward to reveal 2 screws attaching wires. Replaced in reverse order, turned on power, back in service. 10 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hugh from Midland, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake Element Burned Out
It is simple.
Cut off the power. Remove racks. Remove burned out element and replace with new one.
Replace racks and turn on the power. Set the clock.
I've done this about 5 times and now keep a spare element.
Cut off the power. Remove racks. Remove burned out element and replace with new one.
Replace racks and turn on the power. Set the clock.
I've done this about 5 times and now keep a spare element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from TULARE, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burn out the Heating element
Removed burn out element,very easy to installed, screwed them in, done that fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from PLAINFIELD, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The heating element was broken in one place & wouldn't heat
Ordered the part on a Friday afternoon and was shocked to receive the box on Saturday AM! Turned off the power to the unit, unscrewed the screws holding in the old element, and hooked up the new one. We didn't have a socket wrench so we subbed a pliers. So easy & cheap! Seems like everything's breaking around this house & this is the ONLY thing that was easy & cost less than $20! Happy with Parts Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilfred from Freeland, WA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burnt out
Element went out on Wednesday; ordered part on Thursday; it arrived on Saturday (via regular service). Took out old part with hex screw drived, installed new and back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jack from kenner, LA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
bottom element blown
1. isolate the main power supply. 2. remove backplate on old element,remove connecting terminals from old element; and withdraw from oven. 3. connect new element[make sure the connection is firm].replace backplate and secure with the two screws provided. switch on power, oven working perfectly.
Was this instruction helpful to you?
Thank you for voting!