JBS06G4R1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marilee from Newburgh, IN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
The bottom oven heat element didn't work
1. Removed the old element. Had a little trouble loosening the screws. After we got them loose, everything was easy.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a new one.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Littleton, CO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element shorted and broke
TURN OFF CIRCUIT BREAKER before doing anything even if oven is not turned on! If I hadn't checked voltage with tester before starting I would have made a shocking discovery.
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inches
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inches
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Renton, WA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Oven lower Bake Element exploded
First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Warminster, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bottom Bake Element wouldn't heat
First I turned the Breaker off for the Oven. I removed the two screws that hold the element/cover plate. I pulled the element out to get access to wires attached to element & removed screws holding wires to element. I reversed the process to put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Manassas, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element cracked
The repair was fairly easy. Removed the 2 screws that hold the plate to the oven and then pulled out the element and loosen up the screws that connect it. Installed the new element and re-attached the element to the plate and secured the plate back to the oven. This site was very easy to use and very helpful and I will use it again if I need another part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas Minich from South Windsor, CT
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out due to age
Shut off the power at the circuit breaker, removed the two nuts holding the element to the oven, unscrewed the two screws connected to the wire leads, removed the bad element and reversed the process to replace with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Las Cruces, NM
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower baking element had burned out.
Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewall and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!
The time it took was literally a few minutes. Works like a new oven!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Roxboro, NC
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Baking element had burned out and actually cracked in half.
It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven back. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GREGORY from HOUSTON, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake Element Burnt Out On Upper Oven
Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Mountain View, CA
- Parts Used:
- WB30M2
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Shorted out the burner... fat gets into the receptors on these old stoves.
The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Lexington, KY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replacing the bake element
I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct part shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Gahanna, OH
- Parts Used:
- WB44X5082, WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking Element shorted out and burnt
I loosened two screws that held the baking element to the stove and pulled out. Then, with a screwdriver , I took the old wires off and replaced them onto the new Baking Element and reassembled.
It was a very easy task and while I was at it,I replaced the Drip Bowl pans on the top of the stove with Chrome ones.
I ordered the parts on a Tuesday and, to my surprise, I received them on Thursday, and the cost was about half of what it would have cost me elsewhere (to include GE Parts Warehouse)
I highly recommend partselect to all of you that need inexpensive repairs.
It was a very easy task and while I was at it,I replaced the Drip Bowl pans on the top of the stove with Chrome ones.
I ordered the parts on a Tuesday and, to my surprise, I received them on Thursday, and the cost was about half of what it would have cost me elsewhere (to include GE Parts Warehouse)
I highly recommend partselect to all of you that need inexpensive repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Sewickley, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven wouldn't heat
Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is still a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Stuart, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Heating Element Was No Longer Working.
Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.
I put new element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
I put new element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosaire from St. Agatha,, ME
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element was cut
Removed two screws and take Element out and put new one in.It is very easy to do.
Was this instruction helpful to you?
Thank you for voting!