JBS26407 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Littleton, CO
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element shorted and broke
TURN OFF CIRCUIT BREAKER before doing anything even if oven is not turned on! If I hadn't checked voltage with tester before starting I would have made a shocking discovery.
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inches
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
1) unscrewed shield cover to get get at the element screws.
2) unscrewed element screws and removed old element - pulling connecting wires out about 3 inches
3)attached new element to connecting wires (2 screws)
4) pushed new element into place and reattached element connector plate to wall of oven
5) reattached shield cover to wall of oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilee from Newburgh, IN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
The bottom oven heat element didn't work
1. Removed the old element. Had a little trouble loosening the screws. After we got them loose, everything was easy.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a new one.
2. Pulled out the element and disconnected the wires.
3. Connected the wires on the new element.
4. Screwed the element back in.
5. Connected the stove and turned on the oven.
6. It works like a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from McKinney, TX
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Bottom Element On The Top And Bottom Oven Burned Out
Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Warminster, PA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bottom Bake Element wouldn't heat
First I turned the Breaker off for the Oven. I removed the two screws that hold the element/cover plate. I pulled the element out to get access to wires attached to element & removed screws holding wires to element. I reversed the process to put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Manassas, VA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element cracked
The repair was fairly easy. Removed the 2 screws that hold the plate to the oven and then pulled out the element and loosen up the screws that connect it. Installed the new element and re-attached the element to the plate and secured the plate back to the oven. This site was very easy to use and very helpful and I will use it again if I need another part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas Minich from South Windsor, CT
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out due to age
Shut off the power at the circuit breaker, removed the two nuts holding the element to the oven, unscrewed the two screws connected to the wire leads, removed the bad element and reversed the process to replace with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Maryville, OH
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
bake element burned out
took cover off back of stove. Removed two screws and wires that were attached to the element. Removed old element and installed new element. An easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from New Lebanon, NY
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
bake element disintegrated
At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Carrollton, TX
- Parts Used:
- WB17X5051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Range element was intermittent - bad contact at wire
Drilled out the screw on one wire as it was corroded to the metal socket. Sanded both wire terminations. Installed wires into terminal block. Reassembled all loose parts and installed into burner slot. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AL from GENOA, NE
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out in oven
First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Medford, NY
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken broiler element
Replacing the part was fairly simple. Do not forget to dis-connect the element from the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Roanoke, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broiler element not coming on
removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from St Mary's, GA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element failure
I removed the old element and replaced it with a new part. It was very simple.
The power was turned off. The elemnt wiring was removed. The new one was installed in reverse order. Power back on and the oven tested just fine.
The power was turned off. The elemnt wiring was removed. The new one was installed in reverse order. Power back on and the oven tested just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from cape coral, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
lower element did not heat
First shut off power to the store and used a socket set to remove 2 screws and disconnnect the element. Connected the new element but had to use the old screws as the new ones did not work with my appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dora from Port Orange, FL
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out
Turned off power. Removed oven racks. Removed the 2 screws that held the element in place. Pulled element out about 3 in. & disconnected 3 wires. Placed new element, reconnected 3 wires & reconnected the 2 screws that hold element in place. Turned power back on & it works great!!. Was very pleased at how easy it was & also how fast I received the part, which was day after I ordered it.
Was this instruction helpful to you?
Thank you for voting!