JBS05GL1 General Electric Range - Instructions

Snapped in the clip

I was able to remove the heating element but in the process one of the wires fell behind the back wall of the oven so I needed a little help getting it out. It was my first time working with electricity. If this didn't happen the repair would have been quit easy. The instructions were great.

This was so easy I should be a repairman! Turned off power at the breaker, used socket to unscrew two hex head screws, pulled out element slowly from the back of oven wall - enough to expose the wires about 3". Used pliers to remove clips from terminals, put new element in, pushed on new terminal clips, fed wires and terminals back through the two holes, replaced the hex head screws, turned breaker on and wallah! My wife was happy! That's a good thing.

I used a socket set to remove broiler element. It was stiff after so many years, but no problem. All was going well until I pulled too hard on the old element(I'd recommend jiggling if stuck, not yanking) & 1 of the 2 connectors pulled loose & fell behind the back. After my initial panic, I summoned my courage, unscrewed the coverings in the upper back of the stove, found the lost connection, pushed the new element ends through the holes from inside the oven (easiest way to hook it up at this point), plugged it in from the back, pushed it back thru into place inside the oven, reattached everything (front & back), & it worked PERFECTLY! Had I not made a mess of it, it would have taken approx. 5-10 minutes. As it was, it took approx. 15 minutes. EASY!

Simply inserted the clip into the hole in the oven. It took less than 20 seconds. :D

remove two screws slide out. slide new one in. put two screws back. done.

i was really pleased getting the order from partselect. i had torn my oven appart and knew i needed just this one part i came home and ordered it from parts select and actually got the part the next day.... very nice.... so pleased

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

I could not believe how easy it was to repair my own oven! Honestly I was shocked. I pulled the oven out, unscrewed 7 screws, pulled the old element out, placed the new one in, replaced the screws and I was done. All I could think about was how much money I saved! Also, it took me about 15 minutes.

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

This burner element is the large element of a 2 element modual.
After removing the modual, there was 6 small metal screws to open the modual to expose the burner elements. After the burner element were exposed there are 2 wires that had to be disconected with a screw driver. Once the wires are disconnecter the burner element is easy removed by sliding the old element out and sliding the new element in. Just reconect the wires to the new element and put the cover back on with the 6 metal screws. It took about 30 minutes to complete the task, taking time to clean all the insides to bring it back to new condition. Very very easy job.

pulled range out, unplugged unit, took out 7 screws, unplugged the elements, reinstalled elements, replugged, and completed with the 7 screws back in place. The 30 minute time was replacing both the broiler and bake elements. The parts were also delivered in a very timely manner. Could not have been more pleased and was very cost effective.

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm.