JGB900BEKB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from Oakdale, AL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gas oven igniter for a GE Profile XL44
Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert K from York, PA
- Parts Used:
- WB16K10070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed To Replace Burner
Took longer to open the box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter R. from Riverside, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ignter would glow but gas valve wouldn't open
I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hayden, ID
- Parts Used:
- WB16K10035
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
igniter was bad and tube wasblown
repair was easy enough, but the kit came with female ends and needed mail ends. I had to splice old connecters to new igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Shreveport, LA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter went bad
1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ARDMORE, PA
- Parts Used:
- WB49K10037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Hole burned through deflector oven and metal dropped onto igniter and burned it out
Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from SALEM, WV
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The igniter would glow but the gas would not come on.
I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Falls Church, VA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old blackened oven racks
Replaced old with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Hilton Head, SC
- Parts Used:
- WB24T10147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burnt Smell
Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from Falcon, CO
- Parts Used:
- WB13K21
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not ignite
First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Eldersburg, MD
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from FRANKLIN, TN
- Parts Used:
- WB13K10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Laughlin, NV
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
none
slid the old ones out and slid the new ones in. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from North Port, FL
- Parts Used:
- WB07K10232
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The bottom strip had become rusty and looking badly
I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.
Was this instruction helpful to you?
Thank you for voting!