JBP83HHB General Electric Range - Instructions

replaced Plastic Guides

Had to remove rear cover to connect wires, removing them from the front caused the wires to fall into rear.

very easy and clean.

removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.

Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,

First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. This was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.

Pull out Range and unplug from wall receptacle. Open Range door and remove 2 hex head screws with pliers. Screws located at top inside of range door opening. They hold the burner top in place. Slowly lift front of top burner section up and at same time slightly lifting back of burner section since it rests on 2 pivots. Prop front of burner section open, tilted back, with a piece of 2X4 maybe 2 1/2 ft. long. Make sure the 2X4 is located at the front/middle of range [resting on insulation] and at front middle of burner top to keep it opened firmly and balanced. You have about 5 or 6 wire clips to remove from elec. posts. Use pliers to gently remove clips. Tag the wires with tape to remember which wires go onto the new burner. Or take a close up picture with your phone to remember which wires go where. There are 2 philips head screws holding clips that hold the burner in place. The clips are slipped into a slot to help hold them in place. Mark the 2 slots so that when you remove the clips you will remember which slots to put them back into. You will need to hold the burner with one hand while you are removing the last clip as it could just fall out. Remove old burner and install new burner at same angle as was the old burner. You will have to make sure that the 2 clips are in the slotted openings first as you can not put them in place after the burner is installed in the opening. Reinstall the 2 screws into the 2 clips. Hold the electrical pole fittings with one hand while you gently reattach the electrical clips with a set of pliers. You may need to wiggle the clips back and forth to get them on securely. Remove the 2X4 and gently lower the burner top. The hardest part is now you have to slightly lift the back of the burner top while the front is lifted up and maneuver the back to drop down over the 2 pivots. Then the burner top will drop down in place so that the 2 screws in the range door opening can be reinstalled. I don't know of an easy way of making the top of the burner section fall down over the pivots except trial and error. Maybe use a flashlight to look back where the pivots are located while the top is propped open. That may help you visually to see what you are trying to do.

Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.

My friend's husband came over to help. I mentioned that after unscrewing the old bake assembly unit, we would have to capture the wires or they would slip into the back. Before he even had the screws undone, the wires did, indeed, slip into the back. He then removed the back panel and retrieved the wires, pushed them back through the insulation and clipped each of them onto the back assembly. However, the wire clips kept slipping off so he eventually had to criimp the clips to keep them tight on the ends of the bake assembly. That troubled me; what if in the future one of those clips comes loose while the oven is in use? Any suggestions on how to keep these connectors on tightly?

pulled range out,unplugged it,thenI removed the two screws that hold the element in place.take back cover off, then pulled the element out about 3 inches and disconnected the two wires.put new element in,put wires and screws back in place,checked to see if worked,did not work,check and reset breaker,it works put cover back on,push range in palce and done.

It was just a matter of removing 5 screws that attached the broiler coil to oven top. Then carefully removing coil so as not to cause wires attached to fall into the back of the oven. Needed an extra pair of hands to hold coil while i guided the wires back thru the opening. All that was left to do was to secure the broiler coil to oven. All completed in less then 30 mins. A lot easier then originally thought. And, a lot cheaper then getting a repair person to do the job.

I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.

Make sure you turn power off at the breaker, then replace the element.

Tim

This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.

Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.