J335*01 General Electric Range - Instructions

I removed the screws holding the element in place. I pulled the element out from the back of the oven about 3" and then disconnected the two wires. I then reattached the two wires to the new element and pushed the element back flush with the rear of the oven. I then rescrewed the two screws that hold the element in place. That was all there was to it.. Very easy. I am 54 years old and have never done this before.. So if I can do it so can you....

First, turn off the power. Remove the two retaining screws, pull out the broken element far enough to unscrew the connectors, remove the element, reconnect the new element, screw it back in, turn the power back on. Yes, it is that easy! Took me all of five minutes. Took longer to find my tools!

First I removed the two screws that hold the element in place. I pulled the element out and disconnected the two wires that hold it in place. I reversed the process for the new element and viola! The oven works just great. The element actually arrived a day earlier than expected. Thanks Parts Select!

My husband helped me pull the range out from the wall to unplug it, I removed the screws on the hinged bracket, pulled the wiring out a couple of inches and removed the screws attaching the element to the wiring. Then I reversed the process. Easy as pie. The most time consuming part was unplugging the range, but as it is 220v (can kill you) I consider it a nesessary step. The best part was the price and availability. I ordered the part on Sunday p.m. and got it on Tuesday p.m. at half the price quoted by a national chain.

I used a philip screw driver to remove two screws which enable me to pull the wires out about three inches from the back of the oven and replaced it with the new one after disconnecting the wires from the grill. The hardest thing was the limited space.

Turned off breaker,first . Then removed 2 nutscrews and pulled unit out , 4 inches ,removed 2 nutscrews joining the 2 wires and the 2 terminals of the bottom element. Removed bottom unit and replaced with new unit . reversing the process. Turned breaker on and tested the oven. Works fine. Took less than 15 minutes.

turn power off at circuit breaker box, remove old coil from oven, attach the new coil and attach to wall of the oven. Very easy to repair.

First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.

Removed 2 screws (with 1/4" nut driver) on bracket holding heat element at back of oven. Pull element forward to expose the 2 wires connected to element, remove screws on wire corrections with flat head screw driver. Remove element from oven......Reverse the steps to install new heat element.....very easy job....except I cleaned the oven while I had the element out of the oven.

Followed the enclosed instructions

The part arrived ahead of time by mail. I removed the old coil, very simple,, I installed the new one just as easy , Turned on oven and it worked prefectly , its a very simple procedure, thank you

unscrew two screws pull the old element out put in new one and screw back in . We had to wire it direct because our oven had quick connect connectors and this part did not. But it was no big deal and didn't take any time to fix.

The repair was pretty easy. I unplugged the stove and took the 2 screws out that secured the element into the back of the stove. I then used a pair of needle nosed pliers to pull the wires off the element that wasn't working and then attached the wires to the new element. I then put the screws back in place securing the element to the stove and it was done. It took me about 5 mintues and the element worked immediately.

The bake element was completely missing from the stove. There were two wires sticking out of the back of the oven, one with a terminal on the end and the other with the insulation still on and no bare wire showing/ The right side mounting screw was there..

The left mounting screw hole on the oven had been drilled out oversized, so I drilled another hole in the mounting plate above the original., after attaching the element with a single screw.

I removed the one screw, removed the bake element and pulled the electrical wire without the terminal end. Next, I put a terminal on the wire and attached the wires to the element. Finally I installed the element with the two screw into the rear of the oven.

Unfortunately the element didn't work, so my next step is to trace the wiring and determine if a switch or thermostat might be faulty. I have checked the continuity of the wires from the bake element to the thermostat.

More in chaper two..

First I removed the 2 mounting screws that mount the element to the back wall in the oven, then pulled the element out about 4 to 5 inches, then removed the 2 screws attaching the wires to the element, then reversed the process to instal the new element. The only tool reguired was a 1/4 inch nut driver. Did the job in about 5 Minutes. The replacement fit and works perfectly.