J77202 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ROBERT from SEATTLE, WA
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Upper Oven Lower Element Burned Out
Took off the oven liners, took out 2 retaining screws, pulled out element, removed wires, reversed procedure, easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Fort Wayne, IN
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The oven coil burnt out visibly sparking at the failure point on the coil
This model has a top oven and a bottom. The repair was to the top oven. I shut off the electricity to the oven at the circuit breaker box.I removed the grates and unscrewed the two screws holding the burner in place. I gently pulled the burner free along with its two attached wires. I removed the two screws that retained the connections to the burner. I installed the new burner in the reverse order. Turn on the circuit. Good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hubert from Oak Ridge, TN
- Parts Used:
- WB30X356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
A plastic bowl was placed on the hot eye and melted.
The old eye was lifted up, hinge screw removed, and three screws removed from the eye that connected lines to it. Did just opposite for installation. Very easy. The hardest problem was finding an eye with three screw-type connections.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from Helena, MT
- Parts Used:
- WB44X195
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Old element was burned out. Haaven't figurerd out how this happened.
Just unpluged the old one and detached the wires. put the new one in and used a socket wrench to rewire it. . Very easy and was shipped in perfect condition and easy to replace. Very pleased.It fit perfect and oven works just fine. Thank you so much for the service which was very speedy. It was packed to perfection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from San Antonio, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Old drip pans rusted out.
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from cincinnati, OH
- Parts Used:
- WB1X5508
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
broken nylon retention pin in upper oven door
Removed 3 lower screws holding the upper oven inside door panel to the door frame. There is enough flexibility in the panel to coax it away from the frame at least an inch. Removed the old nut plate from inside the door and replaced it with the new one. Screwed in the retention pin and 2 washers while holding the nut in place. Assembled the 3 lower screws to complete the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Tamaqua, PA
- Parts Used:
- WB30X356
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench set
The burner only heated half of the coils
The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter J from Oceanside, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old stained drip bowls
I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from STREATOR, IL
- Parts Used:
- WB30X354
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
element was not heating
I unscrewed the screw that held the element in place and then took the hex head nuts holding the 3 wires off the old element. When taking the wires off, I had the new element next the old and put each on the same connection one at a time to make sure I replaced the wires in the same location they were on the old element. After connecting the 3 wires, I reattached the element to the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from San Jose, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed new Drip Pans
I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!
Was this instruction helpful to you?
Thank you for voting!