JBP75AY2 General Electric Range - Instructions

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

The repair was quite simple. I pulled the range away from the wall. Removved 6 screws from the back panel with a nut driver. I the disconnected the wires from the clock control and then removed the 4 screws securing the control board. I loosened the faceplate from the old control with a hair dryer and removed it with a knife. I afixed the faceplate to the new control with two sided tape. Connected the wires to the new control and secured it with the 4 screws. The only problem one might have is the instructions referenced black and purple wires whereas mine were red and blue respectively. Reattached the back panel with the six screws and plugged the power plug back in. Moved the range back against the wall and tested the oven which tested perfectly. Note please disconnect power before proceeding with the installation of the new part.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

Quite hard to do,had to take out screw that went thru oven door,stabilizing piece fell off .We had to get the two screws lined up and thru the door then screw the handle in.but we did it!

Required new light lens for oven this type has five (5) of them; only the oven temp light lens was damaged. Ordered from Parts Select.com received item fast in seven days. removed rear guard plate, than oven temperture switch than slid the neon light switch off of the light lens.Lens is removed from the front panel. Installation is reverse order.

Took the upper back covering off, disconnected the clock control. The only problem is the replacement didn't have the same connections so I was able to pull up the replacement number of wb27x10311 and asked for a diagram which told me exactly where to plug each of the red, white, blue and yellow wires, what a relief! To my amazement I fixed my "old" stove for less than $160, if I had called GE to service it, I'm sure I would have been looking at a $400 bill. This was the way to go, Thank You!

My husband was able to easily remove and replace the switch and know with-in 15 minutes.

This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

Turned power off, unscrewed the plate, disconnected the element, made sure I kept the connectors out of installation. Squished the new connectors onthe new part a bit. Connected it up. Pushed it back into the installation. and then screwed the plate back on to back of the stove. (Easy - I'm a 50 yr old female.)

replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burner connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.