JBP25G1R3 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Richmond, VA
- Parts Used:
- WB44X173
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Broiler element had flared up and separated
Simple repair that was complicated by not being able to remove the oven door, leaving a long reach to the element connections in the back of the oven. Other than the accessibility issue, the repair is easy. Remove two scews, pull the element out about 3 inches to access and unscrew the screws holding the wires to the element. Then reverse the process with the new element. But, because of the long reach, there were alot of dropped screws and cussing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from N CHARLESTON, SC
- Parts Used:
- WB17X5095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no burnt wire
Replace part an wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ervin from Milford, DE
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
infinite switch would not shut off at times.
First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Placerville, CA
- Parts Used:
- WB31K10265, WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
not heating properly
Unplug coil, remove pan - place new pan, plug in new element and bingo. Took approximately 30 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- A K from LITHIA SPRINGS, GA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven/ No Heat
Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Sinking Spring, PA
- Parts Used:
- WB2X1452
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Still need an other nut to keep broiler support inplcae. Support bar did not come with new screws so I must locate one new one.
I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from WILMINGTON, MA
- Parts Used:
- WB31K10265, WB31K10266, WB30M2
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Needed new replacement surface element and drip pans
Surface element easily unplugged and removed, drip pans lifted out, New drip pans inserted, New 8" surface element and present 6" surface elements Inserted and plugged in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from GARLAND, TX
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broil element burn into
turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lafayette, CO
- Parts Used:
- WB44X173
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
broiler element circuit broke
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KATHY from SOUTH FULTON, TN
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
wire burned on surface terminal block
I am a 62 y/o single female and was able to make this exchange of parts with ease. The toughest was getting the old terminal's wire clips free from years of gunk! I was pleased with the ease of installation and that it really worked afterwards. By the way, thank you Parts Select for getting this part to me very quickly. If a novice can diagnose, find the correct part and install it with success then anyone could do the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Southern Pines, NC
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Surface element was corroded.
Removed existing surface element and replaced with new element.
P.S.
Part Select service was excellent.
P.S.
Part Select service was excellent.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Buffalo, NY
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a drip pan
OK, I put the drip pan under the burner. Without a single problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CALDWELL, ID
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element did not work
Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Cleveland, OH
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
melted electric range element
Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !
Was this instruction helpful to you?
Thank you for voting!