J486Y1 General Electric Range - Instructions

I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!

Removed old, burned out element, and replaced with a new element. The worst part of the entire job was getting the oven door assembled back on to the oven.

removed old element rewired new element,turned back on power

First my husband removed the screws that held the element in place, pulled it partially out and then disconneted the wires. He located the part number that was stampted on the defective element and then I searched the internet for GE parts. I noted the price at GE site and continuted to search. The PartSelect price was about 1/2 of the GE price. We ordered the part, it arrived in two days, and we replaced it in less than 30 minutes. We were very pleased.

I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!

From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!

Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.

TURN OFF POWER , remove oven door & oven wire racks, remove two retaining screws in back of coil and pull the burnt coil foward enough to remove the screws that hold the wires to the coil. You may have to drop one side of the front support bracket to move coil forward.Fasten the new coil to the broiler wires with the new screws provided. Push the new coil back into place being careful not to pinch the wires in the opening. Refasten coil to the oven back with existing screws that you removed. Refasten front support.Put racks back in and put door back on.Easy fix! Easy to order, easy to install and came within days from order date. Very pleased with whole thing.

First turn off breakers. Undo all screws and remove burner. Easy to see how to replace old part with new. Self explanatory if you follow what you have taken apart.

We unscrewed the element easily enough, but had a hard time disconnecting the prongs. Once we did, we had to use a thin screwdriver to open the clamps to fit the new prongs into them. After all was accomplished and we switched on the breaker the broiler still didn't work. Either we did something wrong or the element wasn't the problem. We haven't decided our next move yet; whether to get a repairman in or buy a new oven. It's a pretty old oven/range.

I diagnosed the problem as a burned out element. Received the part the next day (very quick service) My husband replaced the old element with the new. My broiler still doesn't work. I don't blame the company, my diagnoses was wrong. I have called the appliance repairman and it will probably be an expensive fix.

I stripped one wire on the first burner. Then I realized that the terminals were the ones that could be left. Finding a replacement terminal has proved to be difficult. Once I realized my mistake I could change the other three burners very easily.

Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!

Simply removed old and inserted new. No tools necessary.

First I turned the power to the stove off at the breaker box. Next I removed the two screws holding the old element in place against the back wall of the oven. I gently pulled the element forward. I wound a couple lengths of spare colored wire around the two electrical wires before disconnecting the retainer screws at their connection points. This insured that the electric wires would not fall back inside and behind the firewall. I then disconnected the screws holding the electrical wires to the broiler element. I removed the element from the oven and discarded it. I then connected the screws through wires and the connecting points of the new element. I removed the spare wires hold the electrical wires. I positioned the broiler element in place and screwed in the retainer screws securing it in place. I turned the breaker switch to the "on" position and tested the new broiler element. It tested fine. Job done in 15 to 20 minutes. An able bodied person could do it in less than 10 I'm sure.