JBP65AC4AA General Electric Range - Instructions

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Unplugged the stove from wall, pulled out oven racks. Unscrewed 2 screws that attached the burner to the oven. Pulled the two wires off, be careful not to let them go back into or behind the oven wall, then you would need to take the back center panel off and push them back through. But I bent the wire enough when taking them off to make sure they rested on the inside of the oven wall, got the new burner attached it to the two wires, screwed it back in the oven wall and I was done. Plugged it back in and works beautifully. Whole thing took maybe 15 minutes 30 minutes tops.

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

First, I read what other customers posted on this site about how to change the element. =)

I didn't have a nutdriver so I used a pair of pliers instead. They worked fine.

Pulled the stove away from the wall, unplugged it, removed the 4 small nuts holding the small plate over the back of the element connections, slid the connectors off the element prongs, removed baking racks from oven, removed 3 screws holding the element in place, slid element out.

To put the element in I simply did the same thing except in reverse order. The entire process was so easy and only took minutes to complete! However, like another poster, I took the opportunity to clean my oven before putting in the new element.

The best part of dealing with partselect....the element only cost me $51 vs GE site price of $91, Plus the element arrived the morning after I had placed the order! Thank you partselect! In gratitude, I posted my happy experience and a link to this site on my facebook! Thanks for everything!

turn off power to the stove
Pull the stove away from the wall
remove center (metal) wire cover (5/16 nut driver needed)
disconnect 2 quick connect clips
back to the front of stove, open oven door
using 5/16 nut driver, remove 2 screws
pull out old element
insert new element
using 5/16 nut driver, reinstall 2 screws
go back to the rear of stove
reconnect 2 quick connect clips
reinstall center (metal) wire cover (5/16 nut driver needed)
turn power back on
ready to cook

Easy

The element ignited and burnt like a sparkler. I unscrewed the bolt/screws holding it in, and pulled like I had on older models. The clips holding it didn't come undone, but the wires hit the side causing a huge flash. It was still hot, even though it wasn't turned on. You need to unplug the oven, or turn off the breaker. I unplugged and took the back panel running down the middle off (4 screws), and undid the clips. Putting the new one back in was easy. Insert the element ends through their places inside the oven. Screw them in place. Hook the wire clips on in back, and replace the back panel. Installation took less than 5 minutes.

My baking element burned out after being exposed to grease and other remnants of past feasts. After some research the repair seemed straight forward so I figured I'd give it a shot. Overall it's fairly simple, though there are some things to watch out for.

I didn't remove my oven's door, which restricted my movement somewhat. After removing the bolts I was able to easily remove the old heating element and expose the two connecting wires. One wire had much more slack than the other. I connected the wire with more slack first. However, I'm somewhat uncoordinated and doing so caused the other wire to retract within the unit. I had to pull out my stove and remove the back panel, which was easy. The retracted wire was easy to find, but there was no slack available through the back access either. I actually had to unscrew the wire from the thing that is connected to the wire that plugs in to the outlet first. Doing so gave me enough slack to connect the heating element to the second wire. After that I just reconnected the wire to the outlet connection and put the back panel back on!

About 45 minutes in total time. Most of which was figuring out the approach to getting enough slack to connect the second wire and working around the oven door which restricted my movement.

Saw the repair on YouTube first, to get the general idea. Very simple after that.

Unplugged oven.I opened up back of oven the connectors to the heating element were showing. disconnected the wires(they just pulled off)went inside oven took the 2 screws out and pulled old heating element out. Put new element in and fastened it with the 2 screws. Went to back of oven slid the connectors together.Put back of oven back on plugged it in and started the oven. It worked

Took out the nuts that held the old element, removed it, put
in new element with tightened nuts...and it didn't work.
We took off the plate on the back of the stove, found the
element contacts protruding through, attached them to the
wire connectors that were close by, and it DID work. We were thankful it turned out to be easy!

first pull the range out and disconnect power cord
remove back cover (5 screws)
Open oven door and remove racks
remove (2 screws) that secure bake element
pull off 2 wires
put new element in replace 2 screws
from the back of range plug the 2 wires to element
replace back cover
really easy

Using a set of nut drivers, I unscrewed the element from the back of the stove, I unscrewed the thermometer, and unscrewed the brackets holding the element to the top of the oven compartment.

After the element was free, I pulled it out of the back of the oven, exposing the wiring. Using pliers, I disconnected the two wires, retrieved the new element, and re-connected the wires to the new element.

I reconnected the thermometer, pushed the element back into the oven, reattached it to the back of the oven and the brackets to the top of the oven compartment.

burner went out Thursday evening, ordered new burner at 8:30 pm, new burner was delivered Saturday afternoon, removed back panel from range, removed burner, replaced burner, re-installed back panel. Took less than 1/2 hour to replace. Hardest part was finding the correct size socket.(ALL WITHOUT HELP FROM HUSBAND.) Thanks so much for prompt delivery.

I am a recently divorced mom who is too proud to ask for help. When I received the part I took the time to read all of the previous posts. I did exactly as many people suggested: pull the oven out, unplug, clean up since you're back there anyway, used the nut driver to remove the metal plate in back and unscrew the two in the oven, carefully unclipped the electodes from the old element with the needle nose, remove the old element, insert the new element, reinsert the electodes , tighten all nut both in the oven and the large metal plate in back , plug back in, push the oven back in place. I reset the clock and also did what one person mentioned which was to turn the oven on and let heat up for about 20 minutes to burn off any of the manufacture coatings that were on the new element. This did not even take me 15 minutes! I was so proud of myself, I told anyone who would listen! Thank you to all of the men and women who took the time to detail what to do, you made my first repair as a single mom awesome!!