J406T2WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- brian from temple, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
burned/blow out element
pull oven from wall,unplugged.removed back with small hex or screw driver . opened oven slide element into slot screwed two screws in, pushed in two connectipn on back .replaced cover on back .plugged in and put oven back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Oklahoma City, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing bake element
Undid two screws to pull the element out, and another two to unhook it from the wires. Reverse procedure with the new element and baked some muffins. The hardest part about this repair was getting the part. I typo'd my shipping address and had to knock on a neighbor's door!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from San Jose, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed new Drip Pans
I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Tamaqua, PA
- Parts Used:
- WB30X356
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench set
The burner only heated half of the coils
The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tyler from Dannemora, NY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt out
Attached the screws and was done. Unbelievable! Ordered the part at 10 am and was delivered at 11 am next day. Great shipping!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter J from Oceanside, CA
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old stained drip bowls
I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Kahoka, MO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
oven not heating
Delivery of the replacement element was quick.Two days after I ordered. My husband replaced it and said it was easy. He just had to unscrew the old element and disconnect the terminals on the back.I thought I was going to have to buy a new stove,just because my oven element wasn't working. Many thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Lanett, AL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bottom heating element burn out.
got new part delivered two days after ordering. I turned off breaker, used a 1/4" wrench to remove the fasteners holding the heating element to the back inside wall of the oven. used screw drivers (one Phillips and one flathead) to remove the screws holding the heating element to the wires. ensure you pull the wires slight out (easily) to ensure they don't pull back into the oven wall. unplug the element from the wires, install new element in reverse fashion and voila, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Brighton, MI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element broken
Took off oven door, removed screws, disconnected wires took out damaged part. Reversed the order. Job complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Nashville, TN
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element burned out, oven would not get hot
Turned off breaker for oven, removed baking (lower) element, searched website to match up size, shape, and connector-type of replacement part. Placed order and received two days later. Mounted new part in 10 minutes, turned on breaker, and immediately baked fries for children. No problem. Much cheaper and easier than replacing entire built-in oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tauna from Holladay, UT
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bad bake element
Turned the power off. Loosened two screws to take the element out. Loosened two more srews to disconnect the element itself from the power. This job was easy squeezy. Within 15 minutes flat I was back on the couch watching old Seinfeld reruns. Two thumbs up for the peeps at Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eunice from North Providence, RI
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broken bake element
1. remove two nuts on rear of oven wall.2. remove 2 screws holding connection to element. 3. attach element to oven wires w/ 2 screws. 4. reinstaill 2 nuts to oven wall. 5. Test oven.Make sure power supply is disconnected @ electrical box!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from VACAVILLE, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out lower element
Shut off breaker to oven. Removed two screws holding the element. Removed two wires attached. Cut back old wires and crimped on two new eyelet terminals. Screwed wires onto element and reattached. Turned breaker on and tested. Works great. Any girl can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Anderson, SC
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
original bottom heating element melted down into wall
Removed the element and put in a new one. Screw mounted interface to 230 mains involved removing two screws in oven wall and two connecting the main wires. Screws were provided with element. Effortless replacement saved an expensive house call and/or oven replacement. Oven is 44 years old and Parts Select had an original replacement part here in 4 days at new years. Part was only $18.45. Parts Select rocks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Cody, WY
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
bake element broken and bubbled
removed two screws with nutdriver, removed two screws attatched to element. reversed procedure. this took less than 15 minutes. "remember to turn turn off power" Jeff
Was this instruction helpful to you?
Thank you for voting!