Models > JTP48WFW > Instructions

JTP48WFW General Electric Range - Instructions

Jump to:

All Instructions for the JTP48WFW

Customer:: Donald from BUFORD, GA
Parts Used:: WB44T10018
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Top oven not keeping baking temperature

Used a nut driver to remove element the insulation was tight and pulled the wires off before they came out of the oven. I made a small hook out of a coat hanger and pulled the wires through the opening.

1 person found this instruction helpful.

Was this instruction helpful to you?

Customer:: Louis from LEAGUE CITY, TX
Parts Used:: 40A15
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver

Change bulb

Easy

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Rachel from Maryland Heights, MO
Parts Used:: WB44T10018
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Socket set

lower bake element went out

basically unscrew two screws, unplug, plug new one in and screw the screws back in.

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Scott from Troy, MO
Parts Used:: WB44T10018
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

While on self clean, the bake element began to burn

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I plugged in the new element and proceeded to clean the oven which is what I was doing when the problem occured.

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Marilyn from Auburn, WA
Parts Used:: WB41T10003
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

gasket replacement

Took about 15 minutes to take the old one off and put the new one on. Not difficult at all.

Was this instruction helpful to you?

Customer:: Bob from Marcy, NY
Parts Used:: WB24T10065
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

broken switch

This was a wall mounted oven. Turned off breaker. Pulled panel off by removing 6 screws. Pulled connectors off old switch. Removed old switch. Just a friction fit. I used my jack knife to get it moving. Pushed in the new switch and connected wires. (just push on tabs) Put panel back together and turned on breaker. Done, easy.

Was this instruction helpful to you?

Customer:: Bradley from Perryville, AR
Parts Used:: WB44T10018
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver

Heating Element

Removed two screws, removed two wires, installed new element. So easy a caveman could do it.

Was this instruction helpful to you?

Customer:: Robert from SANTA MARIA, CA
Parts Used:: WB44T10043
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Broiler Element Repair

I was attempting to replace the broiler element on the oven, but I discovered that the wiring may be the actual problem. I suggest before you order parts for a broiler repair, that you test the wires to ensure that you have continuity. I will have to trace the wires back to the source (the other element works fine) and see if I can find the problem with the current. I will keep the broiler element I ordered until I can confirm that the old element works.

Was this instruction helpful to you?

Customer:: Darthy from Dacula, GA
Parts Used:: WB44T10018
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Socket set

Bake element was broken and needed to be replaced

The repair was very simple. In fact the biggest challenge was finding the correct socket set.

Was this instruction helpful to you?

Customer:: Damaris from Easton, PA
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Missing oven rack

I opened oven and pushed oven rack inside.

Was this instruction helpful to you?

Customer:: george from Moorpark, CA
Parts Used:: WB44T10018
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Wrench set

Oven heating element was burnt through.

Identified part with Part Select, placed order. Opened the power breaker for the oven. Removed oven door (slides off) to improve access, removed burnt element (2 screw and 2 electrical blade terminals). Installed the new element and tested. Reattached oven door.

Was this instruction helpful to you?

Customer:: Jim from Hyrum, UT
Parts Used:: WB44T10043
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Broiler heating element was not working

Turned off the circuit breaker. Removed 5 screws. Unplugged the heating element and then plugged in the new one and replaced the 5 screws. Very simple.

Was this instruction helpful to you?

Customer:: BETTY from CYPRESS, TX
Parts Used:: WB48T10095
Difficulty Level:: Easy
Total Repair Time:: Less than 15 mins

I needed an oven with three racks, mine came with two.

just slipped it in

Was this instruction helpful to you?

Customer:: Vicki from Irvine, CA
Parts Used:: WB48T10095
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Replaced damaged oven rack

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Was this instruction helpful to you?

Customer:: Douglas from Thornton, CO
Parts Used:: WB08T10002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Socket set

Oven lights were burning out regularly

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

Was this instruction helpful to you?

All Instructions for the JTP48WFW