JBV42G204 General Electric Range - Instructions

Took oven door apart to get to gasket. . . Took about an hour or less. Then I basically cleaned the entire over door while I waited for the part to come. When the new gasket came I started to put it back on. I used springed type clothes pins to hold the gasket in place on the middle part of the door which hold the glass. As I put on the out part of the oven door over the middle part of the oven door, I carefully took the pins off as I gradually slipped the 2 parts of oven door back together. After the gaskets were carefully adjusted to it's proper position, then I put the nut screw back in through the gasket holes to hold the 2 oven door parts back together. Then, I finally put the rest of the door back together. This took about an hour also. Not to bad when you have to do this by your selves. This is the second time I've put in a new oven gasket. The oven is 28 years old, so the gaskets last me about 14 years each time. We hope to keep the oven a few more year before we buy a new glass top style stove. Hope this was helpfull to all you diy's !!! Don

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

I called the local GE appliance & sales place, informed them that a friend of mine had found the part on Partselect.com, after they told me the part was no longer made, could not be found. My friend that found Partselect was going to install it for me himself but then I decided it might be best to have the dealer do it, in case something went wrong. I can not buy another stove because they no longer make the upper/lower stove like this model, I would have to rip out my cabinets! plus I do not have the money they are asking for a new stove.. Besides the fact that I LIKE this setup! 27 yrs. old, top oven was always 50 degrees off, but I know it, so not a big deal..

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Remove oven door, removed Phillips head screws on perimeter of oven chamber, loosened four or five square head screws to facilitate the removal of the old gasket, (this gave enough room/play to pry the oven chamber slightly) then removed the old gasket, and re-assembled the oven, and replaced the door.

My husband was able to easily remove and replace the switch and know with-in 15 minutes.

Removed 3 lower screws holding the upper oven inside door panel to the door frame. There is enough flexibility in the panel to coax it away from the frame at least an inch. Removed the old nut plate from inside the door and replaced it with the new one. Screwed in the retention pin and 2 washers while holding the nut in place. Assembled the 3 lower screws to complete the assembly.

pulled out the old one pushed in the new one

I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.

Worked, don't have to replace an old GE combination range "Microwave Cooking Center" when the surface units rusted out.

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

Simply unplugged the burned out one and plugged in the new one. It worked like a charm.