R530DH1 Frigidaire Range - Instructions

First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!

followed your directions - excellent

Removed the baking element with a nutdriver. Slid it to the front of oven and removed the contacts on the back side. Installed the new element and installed the contacts at back of element. Slid it in the holes on back inside of oven and used a nutdriver to install the screws. It was very simple to do.

replaced old drip bowls with new ones

Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.

They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done

Try to buy new unit from local dealer, was told unit was too old. Went on line to Part Select and found part needed and ordered part. When part came, I removed two screws from in oven and four screws from back of range, discorrected two wire leads from bake unit, removed old unit and installed new unit, connected wires, reinstalled back cover, and installed bake unit to oven with two remaining screws. Job done, oven is now working. The part costs with shipping was around $33.00, new oven $600.00. Thanks Part Select.

first i remove the two screws that hold the element then i pulled the element out few inches out i disconect the two wires and i put the new element back in place 10 or 15 minutes top.really easy

Shut off the power at breaker to range,removed the screws and pulled out the element a few inches to disconnect the wires .Connected wires to new element., screwed it back into oven wall.It's a snap!

1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.

I just had to plug the new burner plate in the receptical
and it works again very well.

Removed the 2 element holding screws, disconnected the element leads & remover element. Replaced with new element.
All in all a real easy job (wish all repairs went this easy)
PartSelect had the element at the house within a couple days (Correct part I might add) which made the wife happy !!

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Unscrewed back of oven the plate that was holding on old element, removed it (plugged into small wire device)
Plugged in new one and replaced screws to hold in place.

The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!