KC535ADD2 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Creston, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bake element shorted out.
After the oven cooled, removed the bake element withe a couple of screws, got on line and ordered the part. Two days later the new element arrived and we put the screws back in with the new element. Problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Edgartown, MA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Lower unit broken, arcing
unscrewed rear connections, removed broken element, installed new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Dubuque, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven element quit heating.
Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Hayward, WI
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat.
I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from LIBERTY LAKE, WA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Range burner coil worked intermittenly
Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Palm Springs, CA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
element shorted out
Bake element went back in very easy. However still wouldn't work. Called repairman and computer chip was shorted out as well. Additional $250.00 later stove works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- helen m from eureka, MT
- Parts Used:
- 316442301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burnurplate broke
ordered a new one and I put it inn.Pluged inn and I was ready to cook!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Burkburnett, TX
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Lower heating element not working
Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Withams, VA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat
My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Temple, PA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element would not heat.
Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ocean View, AL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven burner was burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeannette from West Jordan, UT
- Parts Used:
- 5303051519
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Bake element broke
I just followed the instructions that I found online.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Spencer, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench (Adjustable)
Oven wouldn't heat as element was burned out
I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sheffield, MA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Found bake element cracked
Read the reviews and followed the same procedure. Very east..took about 10-15 minutes.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.
Product shipped same day/next day it was delivered and it was installed less than 30 hours after it was ordered.
Exceptional service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICKEY from CONWAY, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burnt out
Unplugged stove, use nutdriver, removed screws, pulled out old element, put in new one. Done. As prescribed. Excellent help as well as got part the next business day.
Was this instruction helpful to you?
Thank you for voting!