REGS36CW1 Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- KENNETH from SALMON, ID
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
No Heat
Remove defective element and replace with new heating element, bench checked servicable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAMELA from SAINT HELEN, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replacement of oven element
My husband had no problems except the end of the new element was different than the original, but hooked it up ok!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathy from Eatonville, WA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
change baking element
unscrew disconnect wires put new one on make sure you turn off power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Lawrenceburg, IN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
My oven bake element stopped working.
It was too simple. I unplugged the oven. Unscrewed the old element. Disconnected the wire plugs from the element. Plugged the new element in to the two wires and screwed the new element in to the back of the oven. DONE! There are several Youtube videos that document this process if you want the visuals.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doris from Efland, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bottom burner not working
I just watched the video, unplugged the stove, attached the burner and started baking again. DSC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- timothy from tulsa, OK
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
element burnt out
unscrew 2 bolts and plug in 2 wires shipped and received in 1 day during christmas was suprised
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbia, MD
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven not heating properly
Replaced the baking element by removing two small sheet metal screws and unfastening the two medal clip/leads. Replaced the heating element, reconnected the leads, and refastened the screws. Took not much more then 5 to 10 minutes and the oven now heats perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Dayton, TN
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven element burned out
Plugged in new element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- eleane from CLERMONT, IA
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
my baking element broke in half in my oven.
I ordered the new part and looked online how to repair it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from St Clair Shores, MI
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element fell apart
Easy! Unscrewed two screws, removed old element and replaced it with new one, then put back the two screws. Saved on a service call. Nothing could have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Wetumpka, AL
- Parts Used:
- 5303051519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out
The appliance repair service had never heard of this old brand, but I was able to order this and have it shipped at a more economical price than any other appliance parts service. All the repair service had to do was to walk in and install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WAYNESVILLE, NC
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Stove wires were not long enough.
Required taking back of stove off to properly extend the wires to plug in the new element as well as crimping existing plugs to obtain a secure contection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Shelby, OH
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bake element was broken
Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lincoln G from Jupiter, FL
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Bake oven failed to heat due to break in element
Unplugged stove. Removed oven racks. Using 1/4" nut driver I removed two screws from back wall of oven that were holding bake element in place. Pulled stove from wall, removed lower back panel. Disconnected electric saber connectors. Pulled old element from oven. Put new element in oven. Reinstalled the two 1/4" screws. At the back of the stove, I reconnected the two push-on saber connections. Replaced back panel. Pushed stove back in place. Plugged in the power cord. Checked oven. Works fine.Great experience with Parts Select in every way.Total work time: about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Independence, KS
- Parts Used:
- 5303051519
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The lower heating element in the oven did not work
I ordered a replacement heating element for the bottom of the oven. All I had to do was to remove one screw on each side holding the element in and supposedly pull the element out to expose the spades on each end to unplug them and plug the new element in. As I did that, I touched the metal case of the oven and welded the spade off of the old element. I couldn't pull the old element out into the oven. First lesson---unplug the stove before doing this! I think that the reason I couldn't pull the rods of the element out into the oven is because they were tangled in the insulation. I then took the back of the stove partially off, pushed the rods out the back holes to expose the spades. The one that was melted could still be pulled out, so then I just plugged the wires to the spades on the element, pushed them back and put the screws back in on the inside. Another tip would to have a screwdriver that fits well. These were really tight, and you could strip the heads of the phillips slots. Anyway, the stove works fine. I could have pulled the elements with the wire into the oven, but since I had a welding job because I didn't turn the electricity off, it took me longer.
Was this instruction helpful to you?
Thank you for voting!