RS35BAW0 Frigidaire Range - Instructions

The problem was that there was heat in the oven but only a little. This threw me off at first but my wife tells me that the broiler element is used as the oven heats up. So bottom line is, the main element was burned out and once I replaced it, everything worked fine.

just insert

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

very easy

removed 2 screws removed clips on old heating element installed new element by placing clips on new part screwed element to back wall of oven total time about 5 min note this stove was 25 years old and part was still available sweet

Please make sure the oven is off before working on oven.
Removed element by removing the 1/4 inch bolts. There were spade lugs attached to it end of element inside hole around insulation. Be careful as to not let spade lugs slip back into hole. I left it attached to broken elemnt piece until I was ready to install new one. That way it held it into place.
Cleaned out the oven of all the fragments with a rag and warm bucket of water... Installed new element. Turned on oven to about 200 degrees F. for about a half hour to dry out and bake out any impurities

removed 2 screws , pull element forward , disconnected connector . pushed connectors on
the new element, pushed the ends back in place
and 2 screws and done . like 3mins.

i removed the 2 screws that held the elrment in place. then pulled the element out about 3 inches and disconnected the two wires , reconenected the 2 wires to the new element and pushed it back in and replaced the 2 screws. the only part available locally was through a service man who would not sell it without installing it. at twice the price plus a service call.

Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

I ordered a replacement heating element for the bottom of the oven. All I had to do was to remove one screw on each side holding the element in and supposedly pull the element out to expose the spades on each end to unplug them and plug the new element in. As I did that, I touched the metal case of the oven and welded the spade off of the old element. I couldn't pull the old element out into the oven. First lesson---unplug the stove before doing this! I think that the reason I couldn't pull the rods of the element out into the oven is because they were tangled in the insulation. I then took the back of the stove partially off, pushed the rods out the back holes to expose the spades. The one that was melted could still be pulled out, so then I just plugged the wires to the spades on the element, pushed them back and put the screws back in on the inside. Another tip would to have a screwdriver that fits well. These were really tight, and you could strip the heads of the phillips slots. Anyway, the stove works fine. I could have pulled the elements with the wire into the oven, but since I had a welding job because I didn't turn the electricity off, it took me longer.

Unscrewed and unplugged old element, then put new one in it's place. Quick delivery and satisfied with DIY job.

Took the old element out in order to order a new one and found that the ends of the wire connectors were almost burned in two. Ordered the new element online and while waiting for it to be delivered, I went to the hardware and bought new ends for the wires and replaced them. Then when I received the new element it took about 10 minutes to finish the repair. We discovered the element burned out on Monday evening, ordered the part and installed it on Wednesday afternoon. It took less than 48 hours from the time I ordered the part until my wife was baking again.

Took the back off the range to remove terminals from the element then unscrewed the two screws holding the element on from the inside of the oven. Installed the new element, put terminals on element and reinstalled the back of the range.

Required taking back of stove off to properly extend the wires to plug in the new element as well as crimping existing plugs to obtain a secure contection.