FGFL77AQB Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- larry from 775, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not light
pulled drawer out and took old igniter off and replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Danville, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not lite
First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Waco, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replaced oven igniter
Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working over the oven door,but I am old. Good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Houston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven Would Not Light
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Ocala, FL
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
originaldrawer guide was cruched out of useable shape
first thing was to remove the crushed guide with pliers and a twist it was out. to install the new one islipped one side into the slot and took pliers and applied pressure on the lower glide into the slot; it was done presto. works like new. thanks,
Fred . it was so reasonable i got a spare.
Fred . it was so reasonable i got a spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M. Nicole from La Mirada, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Haines City, FL
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not light and gas would not come through.
I unplugged the stove then pulled the disconnected the wires that controled the igniter. I took the two screws off that held the igniter to the pilot port. I hand to cut the wires on the new igniter to some-what match the lenght of the broken igniter. Then I cut the connectors from the old part and used the fire resistant wire nutes that where included with the new igniter and connected it all. Put all the screws in tight, double checked every thing. Finally I plugged it in and it was working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Tupper Lake, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat up
First I removed the two screws that held the element in place.I then pulled the element out and cut the wires.I used wire nuts to put the new wirers on and put it back in place with the two screws.I tried it and it worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jody from Storrs Manfield, CT
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not heat.
Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripped wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Poteau, OK
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven drawer would not open or shut completely
first I emptied the contents of the drawer,then pulled drawer open to it's fullest, then lifted drawer so as to tilt slightly, then removed drawer by continuing to pull straight out. then I removed the glide from its protective packaging and inserted it in the same spot as the broken glide was at one time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Darragh, PA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from canastota, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
oven would not lite
took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frances from Hauppauge, NY
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
over draw was off track
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from WEST UNION, OH
- Parts Used:
- 3051162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One guide was missing and the other was broken
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from bossier city, LA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not allow gas to flow for igniter to light
removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since
Was this instruction helpful to you?
Thank you for voting!