FEF389WECD Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- raymond from irvine, CA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven not heating up
ordered new heating element, arrived promptly as expected, compared new heating element to old one and it matched in size only diameter a little different, removed two sheet metal screws holding element in place and pulled out element to expose conductors and removed them with screwdriver. Installed conductors on new heating element slid into holes and installed screws, turned power back on(first step is to turn off power) turned on oven to preheat and she worked like a new one. Thank you PartSelect. Saved me a bundle,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KaShira from Wilmington, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat
My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donnel from COEUR D ALENE, ID
- Parts Used:
- 316083100
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Second replacement of switch that disintegrated with minimum normal usage.
Removed old switch, moved the one wire to the same pin on new very cheaply made but expensive made in Mexico switch, replaced switch, pugged range back in too AC, operated new switch, created sparks and smoke. Element now glows to max immediately when turned on. Replaced stove problem gone!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from SAINT PAUL, NE
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element burned out in the house we rent
Easy as removing 2 screws, pulling the wires through the back wall of the oven so I could connect the new element and replacing everything. Honestly, it only took around 8 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from ALBANY, OR
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Burned out bottom oven element
Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Prosser, WA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element burned out
unfastened clip at back of oven w/screwdriver. Pulled out the plug, unplugged the element. Plugged in new element, pushed back into place, refastened clip to hold it in place at back of oven.. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from WESTMINSTER, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
No oven heat, but the broiler worked fine. All top burners worked.
Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor A from ATTICA, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt bake element
open the door take out the racks.unscrew the holding screws for the element,pull it away from the back wall of the oven. take off the wires carefully and reverse the procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JONESBOROUGH, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burn into
Remove the old one and replaced the new one. It was very simple, fast, and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from CLEVER, MO
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element cracked and stopped working
Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done
unplug the wires and then reinstall the new one and put screwes back in and you are all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from JACKSON, MS
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned element !
replaced the element !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from JAMES STORE, VA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bottom oven element was burnt out
Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from STUART, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burnt out and snapped and appeared to try to arc-weld itself back together?!!
Just followed the very simple video instructions…it took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from BADEN, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element in oven shorted out and started on fire
really easy unscrew the element from the back of the oven unclip remove old one slide clip on the new one and screw back to back of oven. Took 10 minutes or less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from KLAMATH FALLS, OR
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element burnt in half
All that was needed was to unscrew two screws holding it to the back of the oven and pull it out to get to the wires. Then unhook the wires and install new one. Less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!