KTM4829A Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replaced drip pans
i removed the stove eye and the old drip pan. then i placed the new drip pan in and replaced the eye. the new drip pans fit way better than the ones that i took off of it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from LIBERTY LAKE, WA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Range burner coil worked intermittenly
Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from West Kingston, RI
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer glide
First i removed the drawer. Then i removed the broken drawer glide and replaced it with the new one. Then i put the drawer back! The parts were a perfect match...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Myles from Twin Falls, ID
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken drawer glide
I used a screw driver to pop the broken glide out and then snapped in the new one. The repair took all of about 30 seconds. It probably would have taken even less time if the former owner had not epoxied the broken piece in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Reginal from Tampa, FL
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I accidently threw away the drawer glide, when it fell off one day b/c I didn't know what it was. Later on when I started pulling out the bottom stove drawer, I discovered that it wasn't gliding properly....duh...
I just placed the new glider in place and put the drawer back on its hinges and it was good to go... my wife was extremely happy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from North Beach, MD
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken drawer glide
Simply secured new glide into slot. I was more impressed at how easy this company made it for me to find the part I needed. And, they shipped immediately. This company is great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Jacksonville, FL
- Parts Used:
- 5303051140
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broil element was burned out
took out old element put in new one and oven works as good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Crossville, TN
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear door glides and both broken off completely
Part of one of the glides was still inside the hole so had to use a screwdriver to push it on out and simply put the new glides in both rear holes "very easily". Sure am glad I found this site on line. If anything else goes wrong, I will surely contact this site. Thanks. The speedy service was wonderful too. Got it in two days! Carol A. Lawless
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carrie from Torrance, CA
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic piece broke and I had to replace it to hold the drawer in place
Snapped in the plastic piece after I actually ordered the right piece....wasn't paying enough attention when ordering and didn't have a book that showed the image so I could make sure....went off the image on your website......which is awesome. Totally my fault. Thank you for your wonderful service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Pittsburgh, PA
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Intermittent heating element function
Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.
Was this instruction helpful to you?
Thank you for voting!
Renewed drip pans
Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from cincinnati, OH
- Parts Used:
- 5303935058
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
heating elements not working
prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lampasas, TX
- Parts Used:
- 5304409888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from vienna, OH
- Parts Used:
- 5303051140
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
part was spected for it's size and wattage for a custom built oven
I made a 4' h 3.5' w and 7.5' long powder / ceramic coat oven capable of 700 degrees f. the elements were chosen due to their size and capabilty. I am useing -5- 2950watt elements split on 2 40 amp 120v coil contactors regulated with a PID and thermocouople.
Was this instruction helpful to you?
Thank you for voting!