GLEFM97FPBD Frigidaire Range - Instructions

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

I am a DIY kind of wife. My husband works late most nights and I get home in the afternoon. It was really quit simple except for the element plug slipped into the back of the stove. So I had to pull the stove out from the wall and take a couple of screws out of the back and push the plug back through. It was scarry for a minute but it all ended up just fine and we had a wonderful dinner that night.

Step 1 Clear frame surface of any debris Step 2 Back out four (4) screws in bottom of glass holder Step 3 insert glass in to the top and allow to drop into the bottom channel. This may take some finesse Step 4 tighten 4 screws Step 5 clean up area and pick up tools

Quite easy: Removed the two hex head screws with a 1/4 inch nut driver. Gently pulled the old element out of the rear of the range with the connectors still attached. Next I disconnected the connectors from the element and attached a small "paper binder" clip to each of the connector wires to keep the connectors from pulling back through the "Hole". Lastly, I connected the two connectors to the new element (released the clips) and gently pushed the unit back into place and re-secured the hex screws. ALL DONE! Very very easy....

repair was exceptionally easy. Did not need the fiberglass tape that was mentioned in online repair steps. Just slipped the wires off and then back on the new element. Any 70 year old can do.

moved the range out to access back
removed 5 screws from back panel
removed 1 screw from thermostat installed new one
replaced screws, done in 20 minutes
problem solved

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.

Oven is working great now.

Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.

If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.

Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.

Thanks

With no install instructions (NOT good for diy-ers), looked through reviews and watched video for help. Replacement part - not same as original. Had to use magnifying glass to id the terminals / take a picture before disassembly. reassembled - found out terminals are different & black wire is too short. Took off element - rotated the clips one number counter clockwise, reassembled - removed black wire from harness for extra reach. Hooked up, lowered top for test. power on - everything OK. Power off - complete assembly. Power on - test. Seems to be good. When I called customer service for assistance because there was no instruction, they told me I should contact a local appliance repair person. (big joke).

turned power off at fuse box took of back panel about8-10 nuts unhooked wires with pliers that went to element then took2 nuts out that held element up and 2nuts holding element took out and put new one in works great

Went well, and working thank you ??