KP532LW2LUSTER Frigidaire Range - Instructions

I just plugged it into the receptacle on the stovetop and turned the thing on, and it worked! I'd been without the 4th burner for quite some time. Nice to have it back!

Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.

I've been to many appliance repair stores looking for White-Westinghouse Stove Parts and have been told their 'unavailable'! Then I checked PartsSelect.com- and they were listed as 'available'. The 6" & 8" Drip Bowls shipped quick and arrived packed well. The new Drip Bowls aren't as heavily made as the originals- but they are exact replacements and very easy to replace. The wife is happy and with many replacement parts & how-to-videos for repair we plan on keeping this stove for another 20 years!

Instructions included with terminal block assembly. Toughest part was to strip the insulator off of the old wires on the stove. I was originally going to just purchase one but after looking at the other terminal blocks and seeing the burnt insulation and some of the wire strands, I just replaced all 4. PartSelect customer sevice was very helpful to confirm the correct part number I needed for my stove.

very easy

Replace the old ones with the new ones. Was VERY impressed with the quick delivery!!

prepared the parts as directions displayed, removed the heating coils and popped the hood on the range, simple curcit 2 wires in to the main harness for each coil. snip, plug and twist add heat wrap to seal the new conections and done very simple fix saved me buying another oven....for now

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

The unit is 29 years old. With the 250V breaker off, I removed knobs burners, pans. Removed 4 short and 4 very short screws under knobs. Remove the four tiny pointed screws under the burners to free the top. Propped the top up at an angle with lighting underneath. All 4 switches are now free from control panel. Replaced defective switches while keeping detailed labels on all wires while they are free. Replacement switches had same labels on them as the old ones (H1 H2 L1 L2 P) so wiring was easy. Some connectors needed to be crimped a little tighter. The old switches had low and high amp ranges depending on whether they were for small or large burners while the replacements handled either. Cleaned whole unit. The trickiest part was getting the height of the replacement dial posts right. For one dial the right plastic adapter sleeve went shallowly into the dial while for another the same style adapter penetrated more deeply. Note the adapters have a slot along their shaft that allows them to close slightly in circumference. It is easily possible to crimp down the metal dial posts too far. This did not happen but for one dial I had to hack saw the adapter shorter. Reassembling the control panel is two steps where the short screw attaches the switch to the stovetop and the longer screw attached the switch to the control panel and stovetop. I used the awl for aligning the screw holes. Note, angling the stovetop too far (like the hood of a car) can pull wires off the switches. I think the lens acts to hold the lamp in place but since the lens arrived later, I taped the lamp in place and popped the lens into the assembled unit later. The repair worked well. Two switches cost about 75$

Very simply following the online video instructions.

After two failed attempts to get the 'correct' drip pans for my range from two other supply outlets, Part Select had the proper drip pans for this model. They fit perfectly! Simple installation and threw away those cheap, poorly fitting replacement pans I've put up with for three years! Thanks Part Select for having the correct parts!!

The parts came quickly. I removed old drip pans and snapped the new ones into place. A child could do this. Now my cooktop looks new and I am not ashamed for anyone to see it.

I did the repair in less then 5 minutes. I took out old element and put in new one and turned it on and I had heat. Works great Thanks the part came in 2 days what a wonderful suprise that was.

purchased correct part from PartSelect and it fit like a glove!

Pull out the old one. Plug in the new one and your good to go.