CFEF3043RSD Frigidaire Range - Instructions

real easy with no problems, thank you

After a power outage or bake and broil features stopped working, but the rest of the appliance worked fine. I wasn't sure if it was the clock part or the temp probe, but decided the cost replacing both parts was less than a repairman. So first, I watched the video link on the part's page...extremely helpful! Then it was a matter of a few screws and unplugging and re-plugging a few wires. I have NO electrical experience, and very little handy-man experience. This is a simple repair that anyone could do. I am most amazed with PartSelect because it literally took 24 hrs after placing the order for it to arrive on my doorstep. And it saved us an estimated $175 in repairman labor fees. I will be telling everyone about our great experience. Thank you!

I disconnected the power cord,took the top back plate off,the switch knob on the switch I was to change,the two screws holding it.pull the old switch out,place the new one in the holder,replaced the two screws that holds the switch and took the wires off the old switch one at a time and placed them on the new one in order on new switch.replaced the back cover and plugged power cord back in.turned range on,it was good. r taite,

I watched you vedio and done just as the vedio told me how to change the switch. When I got the switch on pluged it in turned it on and every thing work great. thank you very much.

Removed five screws from back of range top with nut driver.Lifted wire connectors(4).Replaced old control board with new one.Replaced screws.And Bingo!The whole procedure took about 15 minutes.

I watched the video to make sure I understood what I needed to do. I did just as the video right down to installing the new one before replacing the wires, which was the hardest part the connectors were on tight. Replaced all screws tested to see if oven worked which it did. Thanks for the video.

Took back cover off 2 screws held the switch then moved wires one at a time from old switch to the new one put everything back plugged in stove everything worked

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

Replaced the control I got from you , even though it was a little different the lugs matched up and works great.

Looked up the appliance and the suspect part.(clock/timer). It described the part and what problem it would fix.(no power to oven) Part shipped very fast and installation was quick and easy!!! They even had a installation video!! You can`t get any better than that!!!

First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.

Cut the range power. Removed the top rear panel. Removed the two burner switch screws. Pulled one wire at a time off the old switch and put it on the new switch. Since the terminal location did not match, it was critical to notice the terminal designation on the old and match it to the new switch. Ex., H1 to H1; H2 to H2. Voila! It worked the first time.