FEFL88ABB Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frederic from KILLEEN, TX
- Parts Used:
- 316555800
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Old element connections different from new element
Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center portion was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Chicago, IL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Racks needed to be replaced.
Slide out the old; slide in the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from fall river, MA
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Draw Glide Broken Off Bottom Drawer.
New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Forest, VA
- Parts Used:
- 316555800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Element Burn out
Self easy
PS Great service Super FAST.
Thanks Jesse
PS Great service Super FAST.
Thanks Jesse
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Armando G from Alice, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Electric burner switch shorted out.
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from VESTAL, NY
- Parts Used:
- 316555800
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
One section of heating element failed to heat.
Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Elberon, IA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large burner wouldn't heat
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.
Was this instruction helpful to you?
Thank you for voting!
Both front burners began heating too fast and too high. One damaged the finish on the splash pan.
At the Frigidaire parts website, I found the parts and saw that there are videos that show how to replace the burner controls. In brief:
1) Slide the range/oven out so you can get to the back of the control hood.
2) There are three screws that hold the cover in place (the video showed four).
2a) The video also suggests using a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that.
2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it!
3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot.
3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong.
3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch.
3c) Use the two screws to attach the new switch in its place and replace the control knob.
4) Repeat for as many switches as you purchased. I did all four.
5) Replace the cover.
6) Slide the range back into place.
I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.
Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.
1) Slide the range/oven out so you can get to the back of the control hood.
2) There are three screws that hold the cover in place (the video showed four).
2a) The video also suggests using a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that.
2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it!
3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot.
3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong.
3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch.
3c) Use the two screws to attach the new switch in its place and replace the control knob.
4) Repeat for as many switches as you purchased. I did all four.
5) Replace the cover.
6) Slide the range back into place.
I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.
Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from CHICAGO, IL
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Error message on display ff30
Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed new ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendell from Ocala, FL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven racks rusted
Ordered new racks and replaced them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Hamlin, NY
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Drawer Glide
It snapped right into the drawer, was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerrold from San Marcos, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
switch not always turn off
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.
Was this instruction helpful to you?
Thank you for voting!
The front left dual element stopped regulating temperature
Replaced the dual element switch and that fixed it up
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from KENNETT SQ, PA
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven wasn't heating properly for a few months and then stopped altogether
The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.
Was this instruction helpful to you?
Thank you for voting!