FCS388WECC Frigidaire Range - Instructions

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Broil worked on the stove, however in bake mode, the oven did not make temperature. Turned off the stove, unscrewed and inspected coil. I noted there was a section of the coil that had a "corroded" appearance. (it was evidence of the coil being burned out). Checked with a ($9.00) voltmeter, showed infinite resistance. Found the original envelop for the stove taped to the back of the oven from 1973. It has wiring diagram with schematic and noted the coil was 3000 W, 19 ohms.

Bottom Line found comparable replacement online and tested resistance, measure dimensions of the old coil, matched with Watt rating, replaced, tested installed and works great, Oven has been in use for a couple weeks now. New stove would have been around $500.00. Not to mention some remodel work, as the house is old and stove is a built in.

Coil was $60.00 and should buy the time I need until I remodel the entire kitchen.

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Took out the bad element and replaced it with the new element in less than 5 minutes, worked perfect, thanks

Generally straight forward repair with the most difficulty coming from the screws holding the element in place being rusted. Took some wd40 and some snub-nosed pliers to get them out. The wire connections on the back of the element are pretty self explanatory. Lightbulb was an easy change though the bulb connection had also rusted a bit and required some pliers to remove.

searched on the computer for the name and part number that was damaged, found that it was the bake element so i ordered it with part select.com. when it arriver three days later (as expected) i disconnected the gas and electric to the range and simply removed the old element with a phillips screw driver. installed the new element, hooked the gas and electric back up and began cooking again...

thanks partselect..

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

I was required to remove the control panel to access the plug as it had been broken and the switch had been shoved into the unit . It would have been extremely simple if the plug had remained on the outside surface
My son can now clean his dirty oven

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

switch out wires on spark module same burner would not lite
oder burner instead of igniter for four dollars more for new burner and igniter it made sense. Changed burner out burner works
thanks
Ron