FGS379ECC Frigidaire Range - Instructions

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.

Having already removed the old igniter , replaced it with new.

Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed which has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!

first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arrived early than anticipated.

Removed the door from the range, disassembled the door, removed all broken glass fragments, installed the new glass, reassembled the door and reinstalled the door into the range. Straightforward and easy. Keep track of which screws go where and it is a breeze.

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.

took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite

Simple repair ,unplug unit,cut the 2 wires close to heating element,remove elements 2 screws w/1/4 inch nut driver. Cut and strip 2 wires back about 1/2 inch,be sure to cut wires close to element,wirenut both wires together. Reinstalled element,plug unit back in. Done . . . 12 Minutes,ready to bake a cake. .

First turn the thermostat off-cut the wires leading to the ignitor, close to the ignitor side-Remove the two 1/4" monting bracket screws and remove the ignitor install the new ignitor using the same 1/4" screws and reconnect the wires leading into the ignitor, note the polarity is not imp[ortant--use the heat temp-wire nuts provided--close the door and call for heat the gas valve is working fine now....

pulled drawer out and took old igniter off and replaced it

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires....install new element and woalla.........save thangsguivingday thanks to part select .com..........

take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..

Thank You..

took out the cove plate inside oven. romoved old igniter load.cutt and stripped new wire to new ignighter , using ceramic wire nuts supplied. reinstalled all and voila. it's as good as new. PS just for safety sake always unplug appliance from power.

Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working over the oven door,but I am old. Good luck