FEF352AWD Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from Danville, IN
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Element burnt out
The old element burnt a hole in itself and just glowed in an area about the size of a quarter. I unplugged the oven, removed the two screws that held the element and removed it. I plugged the oven back in so we could use the top burners. When I went to install the new element I did not unplug the oven as the controls were off. I did not know the element was hot from the outlet (by design) so when I tried to attach the new element sparks flew and it welded itself to the wire so I jerked it looose. I then unplugged the oven, replaced a blown fuse, and installed the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daivid from North Attleboro, MA
- Parts Used:
- 316442301, 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner wont heat all of the time
removed old terminal block . cut wires and spliced new terminal block and insulated with shrink wrap. Very eazy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from GARNERVILLE, NY
- Parts Used:
- 5304506004, 316085701
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
glass broke while self cleaning.
i had to remove all the broken glass then removed the metal that was holding the glass. set the new glass in the metal strips and screwed it back togethr. i also had to remove the frame from the door in order to get to the inside glass. then i had to put the door back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Union City, TN
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Element caught fire when i preheated my oven
I first turned the power supply off to my oven. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the ends. After that I connected the new element to the wires on my oven and secured the element with the two screws and turned the power back on. I pushed the oven-on button and now I'm back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSEPH from PATASKALA, OH
- Parts Used:
- 316088700
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Inside oven glass was cracked
The repair was fairly easy. The oven door was attached to a spring arm that had one screw holding each arm to the door. Once off, the outside set of screws were removed and saved in a small dish. Each section had 6-10 screws, to it's best to keep each set separate from each other. Each of the three layers (of the door) came apart easily by removing the screws for each section. The inside (broken glass) lifted out, was replaced, and the sequence was repeated in reverse. During the reassembly I was able to clean the other layers of glass that had gotten build-up on them over the years. Total time start to finish was about 30 minutes. Only tool required was a screw driver! Probably saved 100+ dollars!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Ashton, IA
- Parts Used:
- 5303935058
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
burner wouldnt heat
removed element , cut wires, conected wires,replaced element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Chicago, IL
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Racks needed to be replaced.
Slide out the old; slide in the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from fall river, MA
- Parts Used:
- 3051163
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Draw Glide Broken Off Bottom Drawer.
New part arrived, opened pkg. , Pulled drawer out. . . Snapped in new parts. . . . Done!! Saved myself $100. 00.
Was this instruction helpful to you?
Thank you for voting!
Electrical connection pulled off the element
When I pulled the element out of the back panel of the oven to remove it, the electrical connection got caught on the edge of the hole in the panel and disappeared back into the oven insulation. It was difficult to find and pull it back out to reinstall it on the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Armando G from Alice, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Electric burner switch shorted out.
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Elberon, IA
- Parts Used:
- 316436001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Large burner wouldn't heat
Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lise from CEDAR GROVE, NJ
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven light bulb went dark; it needed replacing
Twisted replacement bulb into place easily. Let there be light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Lafayette, IN
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat, broiler still worked.
I unplugged the stove for precautionary reasons.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.
I then removed the two screws holding element in place with the correct nutdriver.
I then carefully pulled out the element and pulled the two female spade connectors off.
I then compared to new element and plugged the new element in.
Finally I screwed in the new element and tested the oven.
It worked again!! I would recommend running the oven for a bit before placing anything in to bake. this allows burn off of stuff on the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Meaghan from HOLLY HILL, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Stopped Working
When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!
Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!
Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from CHICAGO, IL
- Parts Used:
- 316233903
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Error message on display ff30
Slid oven out removed one screw one plug replaced part took 5 minutes.told parts repair the error message and they sent me the correct part in two days will use them again saved me from Repair man wanted 85 dollars just to look at it my cost was 28 for probe and 8 dollars for shipping already helped neighbor with their stove they needed new ignighter 12 dollars repair place want 110 to come look at it this site walks you through repair best service!!!!
Was this instruction helpful to you?
Thank you for voting!