FFGF3011RSB Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Clarence from Bronx, NY
- Parts Used:
- 5304506426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One burner had broken
I put in the part and it went well, I have used other parts from your factory for the same stove so I knew it was going to go easy. The part only required one screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Gratis, OH
- Parts Used:
- 5304506427
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Front burner assembly broken
Easy as pie. I had the new part in my hands in less than 48 hours. Fortunately for me it was a simple fix and I was literally cooking in under 15 minutes. I was a little worried about doing anything to a gas stove, but by looking at the other unbroken side, it was just a matter of snapping together a new assembly. What a wonderful website!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from ELDRIDGE, IA
- Parts Used:
- 5304518661
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven would not operate, & down button didn’t work
6 screws to remove upper back panel, 4 screws to remove control. Unplug wire harness. Carefully remove adhesive backed front display cover & press to new control, & reverse process to reinstall. Exact original replacement part, quick delivery! replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from REAGAN, TN
- Parts Used:
- 5304518661
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not ignite
I didn’t follow the instructions for the igniter
I simply jerked hard on the bottom drawer & it cam out onto the floor . Pulled range out & changed the oven sensor with a nut driver.
Same for the controller, 5 screws with a nut driver to remove back plate & 4 screws holding the controller in place , used the old face plate and it was easy as pie
I simply jerked hard on the bottom drawer & it cam out onto the floor . Pulled range out & changed the oven sensor with a nut driver.
Same for the controller, 5 screws with a nut driver to remove back plate & 4 screws holding the controller in place , used the old face plate and it was easy as pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Roanoke, VA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lacking oven racks on used appliance
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD from VIRGINIA BCH, VA
- Parts Used:
- 5304509706
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Low amperage to gas safety valve no gas flow.
Disassembled inside of oven. Slid away from wall opened back replaced safety valve and igniter. Safety valve was good changed only because it was apart. Resemble and test sat. Kept old safety valve for emergency spare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRADLEY from SHERIDAN, MI
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven wouldn't light consistently
remove oven floor and racks remove two self tapping screws unplug igniter replace be careful not to touch element plug in reverse order to reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vajai from RICHMOND HILL, NY
- Parts Used:
- 5304509706
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Igniter gets hot but wouldn't ignite
I did the repair with the instructions from parts select
It was very self explationatry
Thank you parts select
I saved at least $400.
It was very self explationatry
Thank you parts select
I saved at least $400.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from DETROIT, MI
- Parts Used:
- 5304518661
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No problem
My daughter did the installation and it was quick. She had no problem, and it's working great. She love it. She just use a philp screwdriver to take off the bolt then unplug the control adaptor. From the back then plug the new one in and that's it. Easy as 123
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bennie from san francisco, CA
- Parts Used:
- 5304518661
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Code f10
Easy installation using a nut driver and a Phillip screwdriver.plug in harness connector and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Darragh, PA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from YAMHILL, OR
- Parts Used:
- 316243723
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Wood Burning Oven
The Appliance light was installed in a wood burning oven used by a commercial bakery. The entirely masonry oven is used to cook a specialty product with origins in Brazil.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodate the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.
We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodate the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced.
The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Wappapello, MO
- Parts Used:
- 316243723
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Had to go from nat gas to lp
Replaced uper orifice n adjusted oven as instructed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blanca from Union City, NJ
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replaced theoriginal power cord.
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from WEST ROXBURY, MA
- Parts Used:
- 5304509706
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Gas oven stopped working. I read that it probably was the igniter. Bought a new one to ins
YouTube video I used was for a newer version of the same model stove. Door did not have latches to remove it. It was fairly easy getting to the old igniter but a bit of a struggle getting to unplug it, as the connector was behind a small metal shield in the bottom left corner of the oven. Because I couldn’t remove the oven door, it made it more difficult to undo the screw holding it in. I finally did, and from that point it went smoothly. I was worried that I was going to access it from the back, but I didn’t need to. I installed the new one, turned gas back on, moved the stove back to position, and turned on the oven. Very happy to have succeeded, adding a few more years to the stove and saving money for the installation of the igniter.
Was this instruction helpful to you?
Thank you for voting!