FGGF301DNWA Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Chris from WILLOW SPRING, NC
- Parts Used:
- 5304504897
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Oven was kicking out error code F1
First, I shut the OFF the main breaker. Then, I removed 2 screws holding the thermostat inside the oven. The wiring harness was too short to pull through small opening. I tried to fish the wires out with a piece of wire, but no luck. Eventually, the wiring harness disconnected and I had no choice but to remove entire wall oven from wall cavity.
Before starting this, again, make sure the main breaker is OFF:
1. Remove 2 screws that hold the oven in place. Mine were just below the display panel.
2. Remove silver trim at bottom of oven.
3. The power cable (flexible conduit, running down to the floor inside the cabinet) was too short to pull the oven out of the wall. I had to disconnect the oven wiring at the junction box (again...make sure the main breaker is OFF). I photographed the wiring set-up before disconnecting any wires. Once disconnected, I was able to pull the oven out of the wall cavity.
4. I placed the oven unit on a bar-height stool with a blanket underneath.
5. I removed the sheet metal shield on the back of the oven. (Roughly 10 screws on the sides.)
6. I found the wires to the old thermostat and pulled it through the opening in the back.
7. I disconnected the old thermostat harness, connected the new one.
8. I pushed the new thermostat into the oven and reconnected the 2 screws.
9. Everything looked good. I reassembled the back, slid the oven into the wall.
10. Reconnected the wiring.
11. Turned the breaker back on. Tested and it worked.
12. Secured the stove and installed the trim.
Before starting this, again, make sure the main breaker is OFF:
1. Remove 2 screws that hold the oven in place. Mine were just below the display panel.
2. Remove silver trim at bottom of oven.
3. The power cable (flexible conduit, running down to the floor inside the cabinet) was too short to pull the oven out of the wall. I had to disconnect the oven wiring at the junction box (again...make sure the main breaker is OFF). I photographed the wiring set-up before disconnecting any wires. Once disconnected, I was able to pull the oven out of the wall cavity.
4. I placed the oven unit on a bar-height stool with a blanket underneath.
5. I removed the sheet metal shield on the back of the oven. (Roughly 10 screws on the sides.)
6. I found the wires to the old thermostat and pulled it through the opening in the back.
7. I disconnected the old thermostat harness, connected the new one.
8. I pushed the new thermostat into the oven and reconnected the 2 screws.
9. Everything looked good. I reassembled the back, slid the oven into the wall.
10. Reconnected the wiring.
11. Turned the breaker back on. Tested and it worked.
12. Secured the stove and installed the trim.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from Landover, MD
- Parts Used:
- 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bilb went out
replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Corona, CA
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lens cover for oven light broke.
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert R from Lewistown, PA
- Parts Used:
- 5304505695
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Two of theTop gas burners would not spark
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Foley, AL
- Parts Used:
- 5304524341, 316538904
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Enfield, NH
- Parts Used:
- 316544501, 5304453223
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle Frigidaire built in oven
ordered replacement handle and screws. All set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Saint Clair Shores, MI
- Parts Used:
- 5304534377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Sliced Outlet Cord
I was replacing a range oven hood, so I pulled the oven away from the wall but left it plugged in. I removed the old oven hood, which had an exhaust pipe that was still mounted through the cupboard. While I was preparing the new oven hood the exhaust pipe fell out of the cupboard and cut the oven wire in half. I was able to find the part number on the existing cord and looked up on line. I ordered the part using 3-5 business days and it showed up in 2 days. I was able to attach the new cord, which had an easy clip plug, and secure back to the stove. Very easy and very inexpensive to do.
Was this instruction helpful to you?
Thank you for voting!