FGFB64CJSC Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Glides broke on lower storage drawer
The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from GAINESVILLE, GA
- Parts Used:
- 5304524341
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!
Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- leslie from Pickerington, OH
- Parts Used:
- 5304506004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The glass on the enter oven door was broken
It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Elmira, NY
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing oven racks
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aaron from MILLPORT, NY
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Oven would not heat
Unplug the range, remove racks. Remove 2 screws from the bottom back corners ( this was the hardest part. I used a stubby screwdriver, but a longer one would be better. They are fairly long screws). Remove oven bottom, lifting from the rear. Remove burner cover. Bottom left corner is a triangle cover. Remove this too. Remove the 2 screws holding the old igniter in place. The igniter unplugs easily. ( I used pliers, the plug has a clip, and pliers grip better.) Install new igniter ( it only fits in one way ) reinstall mounting screws and covers. Replace oven bottom. (I didn't replace the 2 screws. The bottom sits solidly, and they are a bit of a pain.) Plug in, set clock, test for oven to fire up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from BANGOR, ME
- Parts Used:
- 5304509706
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
The old igniter no longer worked properly, so I needed to install a new one.
1. Unplug the range to ensure there is no electricity running through the range. The repair can be done with the propane/gas line still connected.
2. If possible, remove the storage drawer for ease of access.
3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.
4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.
5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.
6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.
7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.
8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.
9. Reattach the drawer if necessary and plug the range back in.
10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.
2. If possible, remove the storage drawer for ease of access.
3. Remove the screw from the metal plate in the left corner of the oven. Detach the end of the igniter cord that you find plugged in there.
4. Remove the two screws that hold the igniter in place. The old igniter should fall to the bottom of the range.
5. Take a picture of the two other cord connections that run into the middle of the back wall. This will come in handy for reference when you install the new igniter.
6. Route the longer extension of the new igniter cord through the hole in the metal corner plate, attach the cord, and put the screw back in to secure the corner plate.
7. Affix the new igniter to the same spot the old one had been in, using the two screws from step 4.
8. Plug in the two shorter cord extensions, using the photo from step 5 if necessary.
9. Reattach the drawer if necessary and plug the range back in.
10. Set the clock, then set the oven to a desired temperature to begin heating. If the repair was successful, the igniter will light the gas piped into the range, and you will see a ring of flame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PAINESVILLE, OH
- Parts Used:
- 316067902
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old racks had melted plastic on them.
It was a replace racks not repair. No problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Yuma, AZ
- Parts Used:
- 3051162
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drawer Glide Was Broken
Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from SAN MATEO, CA
- Parts Used:
- 316538904
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Repaired Oven Range Light Bulb
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Manchester, NH
- Parts Used:
- 5303935025
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
burner would not lite
switch out wires on spark module same burner would not lite
oder burner instead of igniter for four dollars more for new burner and igniter it made sense. Changed burner out burner works
thanks
Ron
oder burner instead of igniter for four dollars more for new burner and igniter it made sense. Changed burner out burner works
thanks
Ron
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Ventura, CA
- Parts Used:
- 316088700
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Cracked glass inside oven door -exposed to heat
I used good old commom sense to disassemble and reassemble the frame, handle, internal glass,and inter panel to reach and repace the cracked glass. I must admit I had two machine screws left over during reassembly, but found a home. It is important to identify where each and every screw belongs. This will cut down your repair time. I thank PartSelect for providing great service and assisting me in my time of need.
Marv Dixon
Marv Dixon
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Brooklyn, NY
- Parts Used:
- 316088700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Broken glass inside door of oven
First took apart oven door. then took out broken glass and replaced with new glass.Put everything back together done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from So Lake Tahoe, CA
- Parts Used:
- 5304509706
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Bad oven igniter
It’s a plug in part so other than working on your side while lying on the floor it was a snap. 20-25 mins.
It helps to remove the bottom drawer completely to gain easier access.
It helps to remove the bottom drawer completely to gain easier access.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!