282240B Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary Warren from Alexandria, VA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven was slow to light, strong gas smell, long time to reach set temperature
Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.
It was a snap!
It was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Forest City, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Would turn oven on, gas smell and would not light .
After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from DUCKHILL, MS
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven was slow on lite up
removed bottom plate in oven removed three screws and cut two wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Macomb, MI
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
My oven would glow, but wouldn't heat.
I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.
The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Smyrna, DE
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
glo plug wouldn/t ignite
took out the old (2 screws) put clip on wires and put the new part in. Simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- patricia from mayport, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
oven would glow but would take a long time to light, and you could smell gas
the igniter is real easy to put in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from North East, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven would not light
It was pretty much a plug in. My husband had it done in a few minutes. I want to thank you for your great service with receiving the part.
The oven is working great and now I am back to baking.
Thanks for everything
Christy
The oven is working great and now I am back to baking.
Thanks for everything
Christy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cornelius from Chicago, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Igniter would glow but no gas would come out
First I removed the bottom plate of the oven to get a better view. I then removed the burner plate and the burner. Disconnected the igniter and put in new one it was real simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Inlet, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
igniter would heat up but burner for oven wouldn't
Took the two nuts off that hold the igniter and cut the wires as per directions and used the wire nuts to put them together after I installed the igniter.was a piece of cake and didn't take 15 minutes to do.Oven works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Los Angeles, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No heat, gas smell in oven
Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wayne from Washington, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not light
took off bottom pan in oven and replaced ignitor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Mountain Home, AR
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bad oven ignitor
A friend replaced the new ignitor with the old one...very simple job.
I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.
I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merle from Monticello, IN
- Parts Used:
- 5303935066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven taking long time to start and shutting down while baking
The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peter from bronx, NY
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not heat up smell of gas
i followed some of the tips provided, and added a few of my own. unplug stove from electric outlet. open oven door, remove wire trays. remove the two flathead screws, holding down the oven pan, it should slide out easily. remove oven burner(looks like wings)only one nut holding it in place with 1/4"nutdriver. remove igniter, 2 nuts as well with 1/4" nutdriver. cut wires, leave a good length, and strip(2 wires). install new igniter, strip the 2 wires as well, trim to size, and with the two wire caps provided, make wire connections. tuck any excess length of wires away from igniter. re-install all parts the were orginally removed. plug oven back into outlet. turn on oven, and presto, oven worked good as new. saved a couple of hundred dollars doing the repair myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAULA from AUSTIN, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Top part of stove worked but not the oven
I googled most of the problem I was having. When I would turn on the oven I would have the orange glow from the igniter but I would never get heat. I ordered the part off this website...it arrived the very next day!!! 7 months pregnant I fixed the problem!!! My oven works beautifuly!! Just in time for the holidays! I saved so so much money doing it myself. U to can do it, good luck!!
Was this instruction helpful to you?
Thank you for voting!