282240C Frigidaire Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

took off bottom pan in oven and replaced ignitor

Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in oven, plug in and test.

could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!

wonderful went perfect!!!

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.

cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...

Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.

Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked great.

Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.

1. Unplugged unit and shut gas off.
2. Removed the oven door(2screws).
3. Removed the oven floor(3screws).
4. Removed heat dispersion plate(1bolt).
5. Removed faulty igniter(2screws).
6. Labeled and spliced wires.
7. Connected new igniter.
8. Installed all previously removed parts.
9. Restored power and gas to unit and oven
fired up in a matter of seconds.....Thanks

suspected oven ignitor,went to partselect website and saw
others had same concern and ignitor was the failed part.ignitor was not getting white hot just orange-not enough
voltage going to the gas valve to open it.ordered and replaced
ignitor.repair took about 20 minuets-oven repaired.

The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.

A friend replaced the new ignitor with the old one...very simple job.

I would like to comment on how fast the service was from when I ordered the part online to 3 business days later when the part arrived....very happy about how easy it was to order part and that the part was in stock and delivered so quickly. Thank you very much !! I will recommend Part Select to a friend that frequently orders parts.

pulled stove out to unplug the electric cord. Took oven door off and removed the bottom panel (2 screws) and then removed the burner (2 screws). took off old igniter ( 2 nut screws). cut wires and stripped the coating to wire to new unit.
Attached new igniter to the burner, and put the burner back in place and replaced the screws so unit was stable.
Turned oven on to make sure ingiter was going to light oven, when oven came on, turned oven off and replaced the cover to the burner and the bottom panel in the oven,. Put the oven door back on........
Probably took 45 minutes.
I ordered the part late Friday afternoon, around 3, and the part was here Saturday Afternoon. I was impressed.