CPEF3077QFD Frigidaire Range - Instructions

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

replaced it

I unplugged the Stove/Oven electrical cord from the wall, then removed the oven door by unlocking the door brackets with a flat head screw driver then closing the door to the last position before it closes and removing the door from the stove (found instructions on YouTube - very easy, which is optional), then removed the oven racks. Removing the door made it a lot easier to access the broil element and element support bracket screws using a socket wrench. I removed the screws from the rear cover on the back of the stove with a socket wrench to access and disconnect the broil element wires with my hand (pliers if needed). I removed the old broil element and inserted and reconnected the new broil element wires, then re-installed the rear cover. I tightened the broil element in place then re-installed the element support bracket and screws, replaced the oven racks, re-installed the oven door and plugged the stove into the wall. This took about twenty minutes and the broil element is working fine.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

I followed two very good videos on how to do the repairs. It took longer to clean all the disassembled parts and the glass than it did to actually do the repair.
A word of caution: Be sure to lock the door hinges in the open position before you lift out the door. They must be locked open to put the door back on. It's difficult to lock them open once the door is removed. Also when you replace the screws get them all aligned in the holes before you lock everything down.
The infinite burner switch was pretty easy to replace but watch out for sheet metal cuts when you are removing the back of the stove. I recommend gloves. My stove has a 12 inch infinite burner, but the parts list only mentions a 10 inch burner. Before I ordered it, I had to call the company to verify that it could be used for the 12 inch burner as well.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

Took the back off and replaced the switch for that burner. Got alittle nervous because the switch did not look the same and the connectors were labeled differently, but it worked. Lost the red light button some how during the repair so when I turned the stove on sparks came out the back because the light connector was loose so I did have to order another one of those.

open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.

un bolted the 6 nut driver heads found probe wire un pluged it 1/4 turn from lock it was in and pull out replace slide in new probe 1/4 turn to lock it in place replace nut driver self tappers and test simple!!

Screwed up by not shutting breaker. Shorted out 3 switches. Thought i could get away without shutting breaker that was a costly error. No problem replacing the 3 switches and element switch. Took about 1/2 an hour.Always shut breaker before doing any electrical repairs.

Replaced the oven probe because a no heat problem. also had to replace the oven control. That was a bit expensive but still saved me hundreds not calling a serviceman. By the way, it works like new.....

Removed the heating element to prevent possible fire while waiting on the parts. Three nut-driver screws removed the back cover. Removed each of four wires and attached to new burner switch, one-at-a-time to prevent any screwups with reconnecting the switch. Unscrewed the old switch, Screwed in the new switch to the front panel. Replaced the back panel and *poof*, good as new. Took as long to repair as it did to write this description.

Pulled the range out, unplugged it, removed upper back panel, inserted lens through front of control panel, slid the notch on the actual light onto the lip on the back of the plastic lens. Done!

After making sure it was the switches themselves not the burners that were the problem, it was easy locating the exact parts I needed on PartSelect and the shipment arrived in a timely manner. I had to replace two out of four switches. Using a screwdriver, I detached the display pannel and removed the faulty switches. Then I disconnected the old wires and attached them to the new switches, one at a time. Closed everything up and the "new" range works great!