Models > 48654 > Instructions

48654 Frigidaire Range - Instructions

Jump to:

All Instructions for the 48654

Customer:: Daniel from floyd, VA
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

8" burner would get red hot (High) with knob set on 4 or 5, them cool back down to the correct setting. In a few minutes it would be red hot again.

Removed bottom drawer. Pulled Range out away from the wall. Unplugged Range. Removed 6 screws from top back cover. Removed top back cover to reveal the Infinite Switches behind the knobs. Pulled the knobs off of the Switches I wanted to change. Removed the 2 Phillips Head screws holding each switch. Pulled the wires off of the old Infinite Switch and put them on the new Infinite Switch. I was careful to put each wire on the correct terminal from old to new switch. I then reassembled the Range in reverse order. I changed both 8" Burner Infinite Switches. I was only having trouble with 1 switch. But, upon inspection. Both Switches had burn marks on the top left of the switch.

Was this instruction helpful to you?

Customer:: Richard from Williston, SC
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers

Control Rod On Switch Was Broken Off

I looked at video and followed the instructions from the man in the video. I pulled out range and then unplugged range from electrical outlet. I removed screws from back and took back off. I then took the two screws out from front of switch. I pulled switch out and then removed one of the wires off and placed it in the same place on the new switch. I did same on the other two wires. I then put switch back in place and tighten the two screws on front. I replaced the back on the range. I plugged range back into the receptacle, pushed range back in place. I put control knob on and then turned it on. The eye worked fine. Very easy!

Was this instruction helpful to you?

Customer:: Ralph from Peoria, IL
Parts Used:: 316436001
Difficulty Level:: A Bit Difficult
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Infiniti switch needed to be changed.

Quit after getting shocked. New part had different configuration. Hard to see marking for pull and plug from old switch to new switch. New switch had different configuration. After all that and making sure switch worked, got shocked as stove was pushed back to wall. Some other issues with wiring has a shorting out problem. Maybe time to call a pro or get rid of the stove and get the gas stove we have been longing for. Be sure to match points on pulling and plugging as the configuration may be different.

Was this instruction helpful to you?

Customer:: Eric from Mosier, OR
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Nutdriver, Screw drivers

front left burner was on HI no matter what the dail setting was

pull back panel, 2 screws & one wire at a time.....And don't forget to KILL POWER!!!!super easy works great now and the wife loves it.

Was this instruction helpful to you?

Customer:: Richard from Fort Wayne, IN
Parts Used:: 316067902
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

old oven racks were nasty!

We recently purchased condo and WhiteWestinghouse range needed some love. the old racks were not in very good shape so we ordered new.

Was this instruction helpful to you?

Customer:: ALBERT from LITCHFIELD, CT
Parts Used:: 316436001
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

bad burner switch

removed six screws on back panel and two holding switch on front panel. pulled wire from switch and placed it on new switch,did same with next four wires. put back panel on .DONE works fine

Was this instruction helpful to you?

All Instructions for the 48654