484240A Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from STRAWN, TX
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven not heating properly.
Viewed the video and simply removed the two screws with a 1/4" nut driver, removed the existing bake element and installed the new one. Quick and easy, even for someone who is not mechanically inclined.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from CASTALIA, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Stove Element Stopped Working
Unpluged Oven, Removed 2 screws, unpluged Element, Plugged in new element. Replaced 2 screws, plugged oven in. Done 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from GERMANTOWN, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element broken
Removed old element with a nut driver, 2 screws. Disconnected electric wires on element, being careful not to let the wires slip into the back of the oven. Connected the wires on new element, lined up holes with holes on oven and screwed in 2 screws with nut driver. Done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from MARIETTA, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element in oven burned through
Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bradenton, FL
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Baking element burned out
Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIRANDA from INDEPENDENCE, KY
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element Was Sparking And Coal Hot Red
Unplugged oven, pulled out old element, reattached new one, making sure to be careful with wires, and put on as secure as possible, just like it was before. . . Very easy to fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from BAINBRIDGE, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom heating element burned out.
Unscrewed 2 screws, pulled the wires out and unplugged the old element, plugged the new one in, screwed 2 screws back in, so easy anyone can do this, it's nice to have a second person holding a flashlight but couldn't be any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from PEACHTREE CTY, GA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Oven element broke
Since I had the element out I cleaned the stove. That took me 2.5 hours. Used cold spray and let sit for two hours and wipe out clean took about 30 minutes. Now for the element itself it took me about five minutes to put the new one in. Oven looks and works like new. Just google your repair needed and watch the video. Easy Peasy. Last time I had it done by an electoral repair person for the tune of about $100.00. This time I bought the part and did it my self. Cost less than $25.00 including tax and shipping. No brainer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MOUNT VERNON, ME
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our old element super heated in one corner and broke.
There are two philips head screws in the back wall of the oven to pull. Gently slide the element forward with the attached wires. Pull the terminals off of each side of the element, slide on to new element, push into place, and replace screws. The whole job was done in under 3 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Orefield, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Original Elememt went bad
The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.
The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- raymond from irvine, CA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
oven not heating up
ordered new heating element, arrived promptly as expected, compared new heating element to old one and it matched in size only diameter a little different, removed two sheet metal screws holding element in place and pulled out element to expose conductors and removed them with screwdriver. Installed conductors on new heating element slid into holes and installed screws, turned power back on(first step is to turn off power) turned on oven to preheat and she worked like a new one. Thank you PartSelect. Saved me a bundle,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Hagerstown, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven would not heat up-
Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Darragh, PA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from JAMES STORE, VA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bottom oven element was burnt out
Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Goddard, KS
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven wouldn't heat
using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine
Was this instruction helpful to you?
Thank you for voting!