RE533DW0 Frigidaire Range - Instructions

Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.

(e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) I did have a problem with the wire connectors. they were a little over heated and loose, so I used pliers to ajust the connection.

I removed the two screws that hold the element in place. Then pulled the element out, disconnected the two wires. Reconnected the new elements wires, replaced the screws and the element was ready to go. Worked very well.

***Make sure power is off the stove*** then remove oven racks.
Used 1/4 inch socket to remove 2 screws holding in the heating element, then pulled the element out a couple of inches to get at the wiring. Used pliers to unplug 2 spade clips.
Reversed procedure to install new element.

I just followed the instructions that I found online.

Unplugged the appliance then removed the two screws holding the element in place. Pulled it out about 2-3 inches then pulled the wires off. The replacement element has 90 degree connectors as opposed to the original 180 degree connectors but that didn't affect installation and hasn't affected operation. Slide the wires on the new element, slide the element back in the oven, screw it back in and you're good to go. Trust me, easiest repair to do.

Very easy repair. First and very important step...shut off power to the oven! Then removed two small screws holding element to back of oven, gently pulled it and the wires connected to it toward me, disconnected the wires, connected the new element and reversed the process. However what I really appreciated about this was how easy it was to find the part on PartSelect.com. It was difficult to read the model number stamped on the plate at the front of the oven, and I got 1 letter and 1 digit wrong. But when I did the search, instead of just telling me "not found," it offered a list of model numbers that were close to what I'd entered, and the first one was correct. Very helpful! The online store is very well set up and easy to navigate.

juist loosened nut and pulled element out about three inches, detached leads, reattached new leads and installed.

First, trip the circuit breaker for your stove. Second I removed the two screws ( 1/4" nut driver makes this go quickly ) that hold the element in place. I then pulled the element out about 3 inches ( double check the electricity is off with your tester )and disconnected the two wires from each side of the element. Press connectors on new element and slide back in.

It was really easy. Removed the racks, removed the 2 quarter-inch screws with a nutdriver. Pulled the bad element out about 3-4 inches, enough to unhook the wires attached to the element with spade connectors. Unhooked the wires and removed bad element. Hooked up new element and reversed the process. Thanks PartSelect!

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I cleaned up the bottom of the oven since it is so much easier to clean while empty. Plugged the two wires onto the new burner, slid it back into position and refastened the screws.
The hardest part was getting one of the screws out since it had been rounded over and the phillips slots were worn too, like somebody had failed to remove it earlier. All I needed was a pliers to grip it.

took two screws out disconnected wires and connected new element ,screw back togather in about ten mins and started cooking dinner

Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.

first i removed the two screws that hold the element in place. then pulled out about 3 inches
and disconnected the wires.installed in reverse
order.