F04B350BWC Frigidaire Range - Instructions

I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.

Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into back wall of oven. Don't know what you would do then.

Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

removed screws,unplugged terminal leads,installed new one,back in business.

Shut off power - throw breaker. Oven access easier with door removed - requires removal of two Phillips head screws. Remove two screws holding element in place using 1/4" socket. Pull element & wires out and pull slide in connectors out (had to hold the wire end with needle nose pliers}. Installed element by reversing the removal procedures. Also good time to clean oven.

older range required no tools to repair, pulled old gasket out of notches at bottom of door, popped clips out of pre-drilled holes, folded new gasket ends {2 inches} and pushed into door, pushed clips into place.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

First thing I did was turn off power to the range at the circuit breaker. The repair was generally easy with the exception that 1 screw holding the broiler element support was "welded" into the oven ceiling. I stripped the screw trying to get it out. Fortunately, I had a special tool that allows one to grip the outer edge of the screw while turning it --- and that's how I got it apart. Once the broiler element support was off, I removed 2 screws holding the broiler element itself to the oven wall and carefully pulled the broiler element out from the oven wall and detached the wire clips connecting the wires to the broiler element. I reattached the clips onto the new element and installed the new element back into the oven wall. I then reattached the broiler element support using a another screw (because I decimated the original one). I then turned the circuit breaker back on and turned the broiler on. Woila. My broiler works again! Special thanks to the people at this site who were very helpful in seeing to it I got the correct broiler element. The original ordered broiler element was delivered to the wrong address. The folks at this site sent me another one. To make a long story short, they saw to it I got the correct part. I highly recommend this site based on my experience with them.

Just followed the instructions

I removed the screws holding the element in place. Then I screwed in the new part. No problem at all.

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

Remove drawer. Insert new slide. Install drawer.

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.