CFES365EC4 Frigidaire Range - Instructions

Husband made install in very short time. Nice to have them back in operation.

Trun off power, remove other knobs gain access to panel remove rubber connectors, which gave me access to switch. Study connections install new switch put panel back together,turn power back on run a series of test, all went well.

pulled door off took door apart replaced hinge

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

Turned of breaker to stove. Removed knobs. Removed four plastic nuts under knobs. Removed five screws that hold swith plate in place. Removed two screws that held actual switch in place. Swaped one wire at a time to new switches. (Switch was a newer model so seeing switch markings was critical to correct wire replacement!) Installed in reverse order. All in all. The job was easy and the new swith looks to be of a higher quality. This ia a gee-wiz--when the old switch failed it failed to the full on position. I had a pot of chicken slowly simering on Lo went to the garage to work a project came back in to a house filled w smoke/alarms going off and the burner on full high-glowing! The old switch was dangerous!

I mistakenly took the two screws out of the front piece above the oven. Except for that the time would have been maybe 10 minutes. The knobs all four came off easy and so did the retainer nuts and the six screws holding the metal plate. I took the old switch out after turning off the power. I had the new switch in one hand and removed one wire at a time from the old and put it on the new one. Put the parts back in place and turned the power on and turned the switch on. Works great! Saved about one hundred and thirty dollars from what the repair service charged last time.

Turn off the breaker! Remove the switch knobs. Using a Phillips screwdriver remove the two screws on the affected switch. With a large tip Phillips remove the three screws at the edge of each end of the panel and place it bottom side up on the stove top. Look at the bottom of the switch. Compare those numbers with the numbers on the new switch. Remove the wires one at a time and place them on the corresponding numbered terminal on the new switch. Be sure to put the mounting plate on the stem. Place the new switch in the cover plate and insert screws. Put cover over switches and insert the three screws on each side. Turn breaker on and turn burner switch on. Success!

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair

2 People--removed door, then removed and replaced springs followed by door a brief pictorial of the area even printed on the package would have simplified the project

with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Removed oven door. Removed screws from bottom of door as well as handle screws. Remove inner panel to expose glass. Replaced glass panel and reverse steps. Very easy.

Found a YouTube video similar to the required repair. Took door off, disassembled the door, replaced the right hinge-spring assy, reassembled. Worked great. High quality replacement part from Part Select that was made in the USA.

I went to you-tube and found a video that told me how to remove and expose the hinge. That was all I needed. One stubborn screw was all the problem I had and it was replaced. Thank you for saving me lots of money!! It's working great and I would buy from Part Select again!

I followed directions for replacement of the glass from the web. Replacement was simple and easy.