All Installation Instructions for Frigidaire Range FES367ABD

Customer:: Sharon from Foley, AL
Parts Used:: 5304524341, 316538904
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Kathleen from Lawrenceville, GA
Parts Used:: 318293820
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Burner on top occasionally went to high heat though it was set at low

Replaced the switch...removed old switch and transferred the wires one at a time to the new switch. Seems to working fine..

Was this instruction helpful to you?

Customer:: Jack from Hedgesville, WV
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Heating element burned out

Took screws loose, unplugged old one plugged in new one put screws back

Was this instruction helpful to you?

Customer:: Kelly from Marietta, GA
Parts Used:: 316135401
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Largest burner was not operational

After turning off the power to the unit, we took it out of the countertop and unscrewed the base of the unit. We then unplugged the damaged coil and plugged in the replacement part. We then screwed the base of the unit back on and replaced the unit in the countertop. The largest burner now works.

Was this instruction helpful to you?

Customer:: BETSY from HENDERSONVILLE, NC
Parts Used:: 318053103
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Door gasket was worn, stained and needed replaced

Gasket has pins that line up with tiny holes around the perimeter of door. Just pull the old gasket off, and snap new one ( with pins) in . Used the butter knife to push ends of gasket in hole at bottom of door. Took about 2 minutes to complete and looks AWESOME! simple. simple, simple! This company ships immediately and the product is described properly. I would buy from this company again!

Was this instruction helpful to you?

Customer:: Robert from Glasgow, MT
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven was not heating up to the set temperature. Stopped around 180-200F.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.

Was this instruction helpful to you?

Customer:: Jeffery from Union Point, GA
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Bake element went out on my oven

Took a screwdriver and removed screws attaching the element to the back of oven. Disconnectec the wires from the old bake element. Replaced the new reversing the process. Very easy.

Was this instruction helpful to you?

Customer:: Gerald from Artesia, NM
Parts Used:: 318255006
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Coil melted in half.

First. shut off the power!!! Remove the two screws holding the coil. Next- slightly pull remaining wire to access the plugs. Unplug the wires, remove old coil, replace and plug in the new... Replace two screws.... Turn power on and....... Start cooking! EASY!

Was this instruction helpful to you?

Customer:: James from Milford, IN
Parts Used:: 318394803
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Stove door switch was broken

used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..

Was this instruction helpful to you?

Customer:: Constantine from Vero Beach, FL
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

lower oven element burned up

Used a screw driver to loosen 2 screws and the pulled the tabs off the old element and installed the new element. I am probably the most "unhandy " guy in the world but this was a snap. I am as surprised as anyone.

Was this instruction helpful to you?

Customer:: WILLIAM from RIDGE, NY
Parts Used:: 318254699
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

end caps that hold the stove at proper depth and support control panels broken

repair was pretty simple. i pulled stove out from cabinet and unplugged it. Then i removed the screws that hold the face panel in place and gently slid out panel as far as i could without damaging wires. i had to remove the small switches that control the two two size burners as well as one thermostat on the right side so i can access the nuts holding the plastic end caps in place. i diagramed the color coded wires so i didnt mix them up.took off the old end caps replaced with new caps and put back together.. took about a half hour as this was my first time inside the guts of this stove.. stove is baack in place and as good as new again.

Was this instruction helpful to you?

Customer:: Lorenza from Rowlesburg, WV
Parts Used:: 316217002
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Improper oven heating.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical supply. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Was this instruction helpful to you?

Customer:: Vista M. from Northport, AL
Parts Used:: 318293827
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Unable to control surface burner temperature

Pull range unit from wall. Disconnect power cord. Remove back panel on range(10 Phillips head screws). Pull knob from surface burner switch and remove two screws. Remove and re-connect wires from switch by number on switch. Replace switch and back range panel. Re-connect power cord and re-position range to original spot.

Was this instruction helpful to you?

Customer:: Russell from North Smithfield, RI
Parts Used:: 318255006
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Oven did not work since bake element did not warm up.

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

Was this instruction helpful to you?

Customer:: James from Basking Ridge, NJ
Parts Used:: 316135401
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Element burned out in 15 months

Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Was this instruction helpful to you?

FES367ABD Frigidaire Range - Instructions