FGF337ASF Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Huston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
would not light oven
take off the old by unsceawing it scraw thenew one onput the wires down the back throw the hole put the wires to gather and cap tham plug the elect. back in and turn it on for to test it wow it worked he he ...richard
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Palmdale, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not come on, broiler worked and so did the burners
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
And re-connected the same way.
Peice of cake..
Thank You..
And re-connected the same way.
Peice of cake..
Thank You..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Danville, IL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven would not lite
First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Waco, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replaced oven igniter
Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working over the oven door,but I am old. Good luck
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from ERDENHEIM, PA
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not ignite
The repair was simple - I first needed to test the original igniter with a circuit tester. Once I determined that the part was bad, I simply removed it and replaced it with a new one from Partselect. It was a matter of simply unplugging a few wires and splicing the new igniter in with wirenuts. Fairly simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from bossier city, LA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven would not allow gas to flow for igniter to light
removed broiler front by depressing the indents on the door slides, removed two screws holding igniter cut wires on old igniter and spliced new igniter to existing wires with supplied wire nuts then reinstalled new igniter and tested have been using oven ever since
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marc from troy, MI
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
oven took longer and longer to ignite ,then just stopped.
took out the cove plate inside oven. romoved old igniter load.cutt and stripped new wire to new ignighter , using ceramic wire nuts supplied. reinstalled all and voila. it's as good as new. PS just for safety sake always unplug appliance from power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jODY from GREAT FALLS, MT
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
ignitor wears out, tenants use the stoves as heat sorce
Opened the oven, removed the bottom plate located the ignitor within arms reach, removed two screws and a snap out part. replaced with the new ignitor and put the stove bottom on and waala...DONE
I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana
I have ordered all my parts from Parts Select and have never had a problem. Thank you. Jody in Montana
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Houston, TX
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven Would Not Light
Removed broiler pan drawer,removed two screws on element unplugged wires,installed new one. ,Tried oven, works like it did when new. It couldn't have been easier,plus I saved a bunch of money thank you partselect mike m.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jody from Storrs Manfield, CT
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven would not heat.
Turned the gas and the electricity off to the gas range. Took the two large screws out in the back of the range holding on the first pan. Have to look for them. Took off the single nut holding on the second pan. Used nut drive #10 to take off nuts. Be careful you do not lose them. Took off inoperative unit. Cut wires to unit. Stripped wires which connect to range. Put new unit on and tightened nuts with nutdriver. Spliced wires together and put on wire nuts securely. Taped them to the wires. Put the second pan back, then the first pan. Turned on gas and electricity to test.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Worked fine. Found that the old unit was cracked and had a piece missing. Must use flashlight. Be safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Darragh, PA
- Parts Used:
- 316067902
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed an additional rack
Open the door and slide in the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bennie from san francisco, CA
- Parts Used:
- 5304518661
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Code f10
Easy installation using a nut driver and a Phillip screwdriver.plug in harness connector and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- M. Nicole from La Mirada, CA
- Parts Used:
- 5303935066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I reattached the new piece. It was the easiest thing ever and i'm a woman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricardo from Stamford, CT
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ignition not working
1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clayton from Gulf Breeze, FL
- Parts Used:
- 5303935066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Oven wouldn't heat , glow from bottom, and strong smell of gas
First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.
Was this instruction helpful to you?
Thank you for voting!