GLEF379DSF Frigidaire Range - Instructions

unscrewed old and screwed in new

That was so easy! I found a Youtube Video, verified that mine worked exact same way, found out that I also needed the top plastic part, ordered online, arrived super fast, so I carefully put everything back together. Extremely happy to see it fixed again. Thank you!

After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!

unscrewed brace attached to element without any problem and secured the wire so that it would not fall behind liner. Connector was a bit hard to disconnect so asked my handyman to detach it - I was not familiar with this connection and did not want to break it - he did it w/o problems and attached the new bake element pronto. How easy can it get!

Really easy to replace handle. However, because the new handle does not have the metal inserts to receive the attaching screws (!appearently a bit cheaper to make!), I am concerned that it will not last as long. I could find no reference to new attaching screws so used the old ones...hope it works!

Removed power plug from outlet. Removed metal racks. Used 1/4" nut driver to remove screws. Carefully pulled element straight foreword. After wires were exposed they were carefully removed. Made sure wires stayed outside mounting hole. Put new element in made sure wires were secured to new element. Carefully push back on element to get wires in place. Put screws in element. Start one screw then the other. Then tighten both screws. Plug power cord back into wall" or turn circuit breaker on if you used that option. Turn dial to bake element on and check for prerogative operation.

Took bolts out of back of oven ,pull out element had take electric clips off .Then I just plugged in the element ,push in and tighten up bolts. Turn oven on IT Works Yea!!!!!

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

First, I disconnected the electrical power by pulling apart the plug behind the range. Next, I removed the screws holding the service plate on back of the top panel.I removed the switch knob by gently pulling it from the stem. Underneath I found 2 screws holding the switch in the panel. I removed these with a phillips screwdriver.I was able to pull the entire switch out to the rear leaving all wires attached.The new switch looked different from the original and the wires were configured differently but the wires were clearly marked. By removing one at a time and placing it on the new switch to the corresponding marking,it was a simple matter to wire the switch.I reinstalled the switch in the panel,put back in the screws to hold the switch, slid the knob back on the stem, reinstalled the rear panel,and plugged the power cord back in.The switch worked perfectly.

Simple just remember there is a hinge lock on the hinge just open the door reach down to hinge and lift lock it blends in but its there close the door and pull out the door pull 2 screws on the hinge connecting it to door install new hinge

The part i replaced was very easy.I pulled the stove away from the wall and took the back pannel off. I then unpluged the electrical strip from the unit.There are two nuts holding the unit in place one at each end,there are also five wires on the right side of the unit you will have to mark them before you disconnect them. Then carefully peal the face off the old unit and reinstall on the one. Put the new unit in place, plugin the electrical strip,the five wires,reinstall the back cover,plugin your stove and your done. All this took about twenty minutes start to finish.

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

Checked the burner and no power to heat the burner. removed the old switch and put on the new one.

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.