FEF364FWB Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
my burners would just heat up solid red even when i had controls turned down to 2 or 3. i would have to turn controls off and back on, then they still would just go back to glowing red
This was my first time ever working with electrical issues. My husband is not physically able to do repairs now. Very easy fix. Just viewed video repair instructions and it went exactly as instructed. Within 45 minutes, I had my stove repaired and cleaned and back in working order!! Great results. My range is working perfectly again and Mama is happy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from HOPKINSVILLE, KY
- Parts Used:
- 316135401
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The surface element quit working, when I tried to remove it, the element cracked.
Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from HAMPTON, VA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burnt out baking element
Removed the back panel, disconnected the terminals and removed the old one and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from COZAD, NE
- Parts Used:
- 5304524341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lens cover for the oven light
Very easy just had to pull the wire up that holds it secure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from KNIGHTDALE, NC
- Parts Used:
- 316203200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Broiler broke apart in pieces. Also we found an round honeycomb part
in the bottom of the oven when I was looking to see what was going on. My husband did the repair just as the video described. I suspect this part honeycomb round maybe ceramic piece goes over where the heat is vented from the oven. Where do I get another one of these and how does it attach in the oven-under the burner. HELP I tried to look on the schematics and did not see anything. The repair went fine, except when we turned everything back on it did not work. Then my husband remembered he forgot to plug the new part IN. Once plugged in it is working fine. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- junius from WICOMICO, VA
- Parts Used:
- 316436000
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Burner switch work sometime.
I follow the video on your site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry W. from Oxford, IA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Bake element bad, broiler element OK.
Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dineshbhai from Rincon HWY21, GA
- Parts Used:
- 316436001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
N/A
I had open back cover and remove the switch than replace new switch. Makesure cable conection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Spencerville, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake Element caught on fire
First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MAINEVILLE, OH
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element went out
Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from CINCINNATI, OH
- Parts Used:
- 316400601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven bottom panel rusted away
Removed two screws removed and replaced panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from KEENE, TX
- Parts Used:
- 316436001
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not controlable
Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremiah from Crawfordsville, IA
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The baking element developed hot spots and stoped working.
I removed the baking racks then unscrewed the default screws for the baking element.I then disconnected the electrical leads from the damaged element. I then removed the old damaged baking element and installed the new baking element, attaching the electrical leads after cheking for weak spots in the element. I then re installed the baking racks and started the oven to burn off any factory oils on the baking element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amber from CARLISLE, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element (bottom of oven) burnt through and snapped in two
Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irving from Germantown, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven element broke
It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!
Was this instruction helpful to you?
Thank you for voting!