FEF311SADF Frigidaire Range - Instructions

The simplest repair ever! I just snapped it in and put the drawer back - fixed. I hope I have other repairs this simple.

after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done

I had to replace the switch on one of the large elements. It could and should have been a quicker repair if there would have been some installation/wiring instructions included with the part. Other than that the repair went well.

Turned off power to appliance removed the screws connecting the element. Disconnected the wires from the old element connected the new element replaced the screws and tightened turned power on turned power back on heated oven to be sure it worked. Very simple to do.

The problem was caused by the owner placing an aluminum catch pan under the bake element. The failure of the element was where it was in contact with the pan. The repair involved removing two screws pulling out the element to access the wires. The connectors were the pull off type so I just disconnected the wires from the old element and placed them on the new element, pushed the element back in place and replaced the two retaining screws. I suggested that the owner not place anything in contact with the bake element. Be sure to up-plug the stove plug before attempting repair.

All I had to do was loosen the screws, pull out electrical hookup on both ends, hookup new heating element to elecric and screw em into place. That's it, super easy and I got the part in 2 day : )

Sat on floor, pulled drawer out, inserted new clips, remounted door, stood up, high-fives myself.

Remove drawer. Insert new slide. Install drawer.

Take the screws out of the inside of oven for the element and slide the oven away from way and remove the back and insert the element to the clips and screw the back of the oven back together and plug in again and push back in place. Very easy for my husband to repair.

Remove the 2 nuts holding the element in place. Pull the element out slightly to expose the wires. each side of the element has a wire. Slide the wires off. Replace new element. attach wires and pu the 2 screws back in the element holders.

Disconnected the main electrical plug from the wall for the oven..
Used a nut driver to remove the two screws that held the heating elementin place.
Pulled the element out so I could remove the two wire terminals.
Installation of the new heating element was fairly basic..Oven is working great..

Very quick and easy fix. Used a nut driver to unscrew the bolts. Pulled it out and disconnected the two wires. I was very happy with the wonderful service we received from Partselect.com. I ordered the part Sunday evening and the part was here Tuesday by noon. I payed regular shipping charges. What a pleasant surprise!

The element went out on a Wednesday. We ordered the part the next day. We received it the following Tuesday (Mon. was a holiday). My 16 yr. old son replaced the part within 15 minutes. It was a piece of cake-actually it was a pizza!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!

first I emptied the contents of the drawer,then pulled drawer open to it's fullest, then lifted drawer so as to tilt slightly, then removed drawer by continuing to pull straight out. then I removed the glide from its protective packaging and inserted it in the same spot as the broken glide was at one time

The directions have been stated many time and they are quite simple. Take out the two screws, pull the element so the wire connections come through into the oven. Disconnect the element at the wire connectors and replace. This is a dirt easy job.

The only real area for a potential problem is pulling the wire connectors through into the oven. As long as you pull slow and from the back - right next to the whole, you will be fine. Take the connectors off carefully and you're golden. Easy job.