MEF300PXWD Frigidaire Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from ROCKVILLE, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Broken element
Simple installation took 2 minutes to do...pop on the connectors, screw each end into back of oven...DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from Oak Park, MI
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven wouldn't heat
I removed the 2 screws, making sure not to drop the wires attached. Took off old wires ,then put new wires on new element, screwed it back into place and it was working. sooooo easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from FREDERICKSBRG, VA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner would cutoff intermittently
Pulled out old burner/inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from OCEAN SPRINGS, MS
- Parts Used:
- 316075103
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element quit heating
Turn off power to the stove. Unscrewed the nutholding it in place, pulled the terminals out, replaced the element by sliding the new terminals in place, replaced the nuts holding it in place and done! Turn the power back on and tested. It works again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from CLEVER, MO
- Parts Used:
- 316075103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element cracked and stopped working
Repair was so easy, Just remove the two screws one on each end of element slowly pull element towards you till you see the ends. Carefully
unplug the wires and then reinstall the new one and put screwes back in and you are all done
unplug the wires and then reinstall the new one and put screwes back in and you are all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor A from ATTICA, NY
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt bake element
open the door take out the racks.unscrew the holding screws for the element,pull it away from the back wall of the oven. take off the wires carefully and reverse the procedure
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from JACKSON, MS
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burned element !
replaced the element !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carol from LAUREL, MD
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned through in one spot; oven would not heat
replaced the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from BADEN, PA
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element in oven shorted out and started on fire
really easy unscrew the element from the back of the oven unclip remove old one slide clip on the new one and screw back to back of oven. Took 10 minutes or less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from EVANSVILLE, IN
- Parts Used:
- 5303935058
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Terminal block was bad.
Cut the old block off tied new wires to hot wires . That easy!
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from LANOKA HARBOR, NJ
- Parts Used:
- 318372210
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Left an appliance on surface element and melted paint onto the element
Plug the new element into the space on stove
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LANK from FAIRVIEW, NC
- Parts Used:
- 316075103
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Bake element melted and burned in half
Using small square tip screwdriver (#1 if my memory is correct), removed two screws at rear of oven pulled old element carefully by pulling, removed wire from each side, attached wires to new element, slid to back feeding wire back where they had been, put screws back in, tightened and viola, stove working great. Approximate time to do job, less than ten minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from CHEWELAH, WA
- Parts Used:
- 316442300
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from OCKLAWAHA, FL
- Parts Used:
- 5303935086
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Can't regulate burners
Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same
Was this instruction helpful to you?
Thank you for voting!