CE303VC3D1 Frigidaire Range - Instructions

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

Removed the back panel, disconnected the terminals and removed the old one and installed the new one.

Took old element off, pushed new element on. Piece of cake.

I couldn't explain how to do the job any better than your instructional video does. As long as you follow the video instructions you should have no problems.

Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

I looked up the model number of the Tappan oven on the net, found the part on the PartSelect site, ordered it and it arrived within a few days. The disassembly should have required nothing more than a Phillips head screw driver, unfortunately one of the screws was completely frozen and I managed to strip the Phillips head socket.

The screw was in a very awkward position so I first tried using grip pliers on the edge of the screw - this failed, I then tried grinding a flat spot on either side of the screw circumference and using the flats for gripping - it worked but the screw wouldn't move. Finally, I took a hacksaw blade and cut a slot in the head of the screw. I widened the slot using miniature files and finally made the slot wide enough for a large slot blade screwdriver - this worked. After removing that one screw and maneuvering the broken hinge out of the access hole on the stove front (the break in the hinge was such that this took awhile) the rest of the repair went very quickly.

The oven door was such that I could not see all of the hinge and when the part arrived from PartSelect I thought it was the wrong part. I called your parts return number to ask some questions. The lady who took my call was extremely helpful and we first discussed the part ID, then she showed me how to find a picture of the actual part on your site. After looking at the picture and the diagram I suddenly realized the part was correct - it was just that I thought it was supposed to be installed in a different manner. I'm sorry I didn't remember to get her name because she certainly should be commended for he patience and her assistance. Thanks Again.

I removed the baking racks then unscrewed the default screws for the baking element.I then disconnected the electrical leads from the damaged element. I then removed the old damaged baking element and installed the new baking element, attaching the electrical leads after cheking for weak spots in the element. I then re installed the baking racks and started the oven to burn off any factory oils on the baking element.

Unpluged old one pluged new one in. So good to have a burner that all the coils heat up.

Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.